Sundown Audio Subwoofers

1000 Watt RMS/ 2000 Watt Peak Dual 2 or 4 ohm voice coils Optimized for small ported, sealed, & band-pass enclosures Large aluminum Faraday ring for smooth acoustic response High strength cast aluminum frame Low distortion motor construction High-temperature voice coil wire Spring-loaded terminals Stitched-on “XL” tinsel lead wires The SA Classic sub is a stunning combination of value, power handling, and deep excursion. It features a cast aluminum frame that houses a bulletproof custom 2.5-inch voice coil, robust double-layered Nomex spider, and SPL competition-grade paper cone. These components are built into a flexible design that works well in any type of enclosure.

COMBO DEAL INCLUDES:2 x PSE-6.5 6.5" 250W Subwoofers1 x SAM-600D 600w Class D Micro Amplifier----------------------- PSE-6.5 6.5" 250W Subwoofers Information: Freq. range 20hz-150hzFS 52hzXmax 12mmD4250W RMSMounting Depth 4.5”Cut out 6” SAM-600.1 Information: Our SAMv.2 amplifiers are ideal for all your powersports needs. It is a micro amplifier to fit in tight spaces but don’t let its size fool you, they pack some big power. It is rated IP67 waterproof to withstand full submersion when getting wild off-road or when its time to clean up when the fun is done. The multi-channel amps have built in Bluetooth so a source unit is not needed just sync to your phone and enjoy. When your ready to get serious and add subwoofers the mono-block amplifiers link right to your multi-channel RCA for an easy install.

COMBO DEAL INCLUDES:2 x PSE-8 8" 250W Subwoofers1 x SAM-600D 600w Class D Micro Amplifier----------------------- PSE-8 8" 250W Subwoofers Information: Freq. range 20hz-150hzFS 43hzXmax 12mmD4250W RMSMounting depth 4.75”Cutout 7.5” SAM-600.1 Information: Our SAMv.2 amplifiers are ideal for all your powersports needs. It is a micro amplifier to fit in tight spaces but don’t let its size fool you, they pack some big power. It is rated IP67 waterproof to withstand full submersion when getting wild off-road or when its time to clean up when the fun is done. The multi-channel amps have built in Bluetooth so a source unit is not needed just sync to your phone and enjoy. When your ready to get serious and add subwoofers the mono-block amplifiers link right to your multi-channel RCA for an easy install.

Neodymium motor creates Sundown's highest motor force - as strong as a 2,000 oz. ferrite motor! 3,500-watt recommended amplifier power L arge shorting rings for extremely smooth response Megaroll technology for extremely linear cone travel and low-end extension Cross-cut pole for lowered distortion, improved thermal control, and higher efficiency Heavy-duty cast basket Spring-loaded terminals accept up to 4-gauge wire Stitched-on heavy-duty tinsel leads Solid pole with vent channels and aluminum shorting ring cap T op-plate cooling channels THREE OPTIONS AVAILABLE MUSIC All-around performance Patented Sundown frame Increased airflow for additional cooling Larger, highly linear spider Most Throw/X-Max MUSICAL SPL Higher musical output U-series frame Direct compression cooling Higher Efficiency SPL Extreme output (burp) U-series frame Direct compression cooling Custom cone, coil and progressive suspension configurations available. Standard 3,500-watt rating. RMS may change with custom configuration. Lightweight and incredibly powerful, the Compact Neo V.3 is the perfect combination of musicality and sheer, unrelenting motor force. Using Sundown's patented platform, the Compact features an extended pole piece with a thick shorting ring, plus a custom cross-cut pole piece with a Neodymium cap for increased output and thermal control. The solid, high-velocity pole piece uses CNC cross-cut channel cooling, a series of 16 direct air-gap vents in the back plate to keep the motor even cooler, and a vented top plate/gap.

Neodymium motor creates Sundown's highest motor force - as strong as a 2,000 oz. ferrite motor! 3,500-watt recommended amplifier power L arge shorting rings for extremely smooth response Megaroll technology for extremely linear cone travel and low-end extension Cross-cut pole for lowered distortion, improved thermal control, and higher efficiency Heavy-duty cast basket Spring-loaded terminals accept up to 4-gauge wire Stitched-on heavy-duty tinsel leads Solid pole with vent channels and aluminum shorting ring cap T op-plate cooling channels THREE OPTIONS AVAILABLE MUSIC All-around performance Patented Sundown frame Increased airflow for additional cooling Larger, highly linear spider Most Throw/X-Max MUSICAL SPL Higher musical output U-series frame Direct compression cooling Higher Efficiency SPL Extreme output (burp) U-series frame Direct compression cooling Custom cone, coil and progressive suspension configurations available. Standard 3,500-watt rating. RMS may change with custom configuration. Lightweight and incredibly powerful, the Compact Neo V.3 is the perfect combination of musicality and sheer, unrelenting motor force. Using Sundown's patented platform, the Compact features an extended pole piece with a thick shorting ring, plus a custom cross-cut pole piece with a Neodymium cap for increased output and thermal control. The solid, high-velocity pole piece uses CNC cross-cut channel cooling, a series of 16 direct air-gap vents in the back plate to keep the motor even cooler, and a vented top plate/gap.

Neodymium motor creates Sundown's highest motor force - as strong as a 2,000 oz. ferrite motor! 3,500-watt recommended amplifier power L arge shorting rings for extremely smooth response Megaroll technology for extremely linear cone travel and low-end extension Cross-cut pole for lowered distortion, improved thermal control, and higher efficiency Heavy-duty cast basket Spring-loaded terminals accept up to 4-gauge wire Stitched-on heavy-duty tinsel leads Solid pole with vent channels and aluminum shorting ring cap T op-plate cooling channels THREE OPTIONS AVAILABLE MUSIC All-around performance Patented Sundown frame Increased airflow for additional cooling Larger, highly linear spider Most Throw/X-Max MUSICAL SPL Higher musical output U-series frame Direct compression cooling Higher Efficiency SPL Extreme output (burp) U-series frame Direct compression cooling Custom cone, coil and progressive suspension configurations available. Standard 3,500-watt rating. RMS may change with custom configuration. Lightweight and incredibly powerful, the Compact Neo V.3 is the perfect combination of musicality and sheer, unrelenting motor force. Using Sundown's patented platform, the Compact features an extended pole piece with a thick shorting ring, plus a custom cross-cut pole piece with a Neodymium cap for increased output and thermal control. The solid, high-velocity pole piece uses CNC cross-cut channel cooling, a series of 16 direct air-gap vents in the back plate to keep the motor even cooler, and a vented top plate/gap.

Neodymium motor creates Sundown's highest motor force - as strong as a 2,000 oz. ferrite motor! 3,500-watt recommended amplifier power L arge shorting rings for extremely smooth response Megaroll technology for extremely linear cone travel and low-end extension Cross-cut pole for lowered distortion, improved thermal control, and higher efficiency Heavy-duty cast basket Spring-loaded terminals accept up to 4-gauge wire Stitched-on heavy-duty tinsel leads Solid pole with vent channels and aluminum shorting ring cap T op-plate cooling channels THREE OPTIONS AVAILABLE MUSIC All-around performance Patented Sundown frame Increased airflow for additional cooling Larger, highly linear spider Most Throw/X-Max MUSICAL SPL Higher musical output U-series frame Direct compression cooling Higher Efficiency SPL Extreme output (burp) U-series frame Direct compression cooling Custom cone, coil and progressive suspension configurations available. Standard 3,500-watt rating. RMS may change with custom configuration. Lightweight and incredibly powerful, the Compact Neo V.3 is the perfect combination of musicality and sheer, unrelenting motor force. Using Sundown's patented platform, the Compact features an extended pole piece with a thick shorting ring, plus a custom cross-cut pole piece with a Neodymium cap for increased output and thermal control. The solid, high-velocity pole piece uses CNC cross-cut channel cooling, a series of 16 direct air-gap vents in the back plate to keep the motor even cooler, and a vented top plate/gap.

750 Watts RMS / 1500 Watts Peak Dual 2 or 4 ohm voice coils Optimized for ported enclosures Class-leading 14mm Xmax Double-stacked magnet Vented magnetic gap & pole piece for superior cooling High strength stamped steel frame High temp 4-layer copper voice coil wire High-quality push terminals Stitched-on Mini-XL tinsel leads Through relentless research in our North Carolina Headquarters, Sundown optimized a 2.5” voice coil and a truly unique motor design to get the deepest possible bass response out of a 12” subwoofer. The subwoofer showcases a distinctive motor design, featuring a heavily vented magnetic gap and solid pole piece, enabling exceptional thermal power handling. The spider itself is a high strength poly-cotton blend designed to handle the full capacity of the motor. To provide an additional level of ruggedness the spider is bolted down and glued to the frame. Its motor geometry allows for a remarkable 14mm one-way linear Xmax, delivering excursion equivalent to far larger cones.

750 Watts RMS / 1500 Watts Peak Dual 2 or 4 ohm voice coils Optimized for ported enclosures Class-leading 14mm Xmax Double-stacked magnet Vented magnetic gap & pole piece for superior cooling High strength stamped steel frame High temp 4-layer copper voice coil wire High-quality push terminals Stitched-on Mini-XL tinsel leads Typical entry-level woofers are highly limited in terms of linear excursion, mechanical ruggedness, and thermal performance. Through relentless research in their North Carolina Headquarters, Sundown optimized a 2.5” voice coil and a truly unique motor design to get the deepest possible bass response out of a 15” subwoofer. The subwoofer showcases a distinctive motor design, featuring a heavily vented magnetic gap and solid pole piece, enabling exceptional thermal power handling. The spider itself is a high strength poly-cotton blend designed to handle the full capacity of the motor. To provide an additional level of ruggedness the spider is bolted down and glued to the frame. Its motor geometry allows for a remarkable 14mm one-way linear Xmax, delivering excursion equivalent to far larger cones.

HZ Series Key Features: RMS Power : 10" – 750W RMS / 2.5" Voice Coil Voice Coil Options : Dual 4Ω - High temp 4-layer copper voice coil wire XMAX : Class-leading 14mm Xmax Frame : Heavy-duty cast aluminum basket Cooling : Vented motor gap and pole piece for optimized heat dissipation Durability : Stitched Mini-XL tinsel leads and bolted spider pack Suspension : High-roll surround with progressive spider for smooth, controlled excursion Recommended Enclosure : Ported for maximum efficiency and output

HZ Series Key Features: RMS Power : 12" – 750W RMS / 2.5" Voice Coil Voice Coil Options : Dual 4Ω - High temp 4-layer copper voice coil wire XMAX : Class-leading 14mm Xmax Frame : Heavy-duty cast aluminum basket Cooling : Vented motor gap and pole piece for optimized heat dissipation Durability : Stitched Mini-XL tinsel leads and bolted spider pack Suspension : High-roll surround with progressive spider for smooth, controlled excursion Recommended Enclosure : Ported for maximum efficiency and output

HZ Series Key Features: RMS Power : 8" – 500W RMS / 2" Voice Coil Voice Coil Options : Dual 4Ω - High temp 4-layer copper voice coil wire XMAX : Class-leading 14mm Xmax Frame : Heavy-duty cast aluminum basket Cooling : Vented motor gap and pole piece for optimized heat dissipation Durability : Stitched Mini-XL tinsel leads and bolted spider pack Suspension : High-roll surround with progressive spider for smooth, controlled excursion Recommended Enclosure : Ported for maximum efficiency and output

Sundown Audio HZS Series Subwoofers Purpose-Built for Tight Installs. Powered by Real Performance. The Sundown Audio HZS Series was engineered from the ground up to bring powerful, clean bass to space-limited installations—without sacrificing output, reliability, or thermal performance. Whether you’re working with a slim enclosure behind a truck seat, under a rear deck, or in a stealth build, the HZS delivers the kind of low-end impact you expect from Sundown. Available in 10" and 12" sizes, the HZS is a shallow-mount subwoofer rated for 600 watts RMS and designed to thrive in ported enclosures, though sealed options are also supported. Each model features a 2.5" black aluminum voice coil, a high-roll surround, a progressive spider, and a vented motor design that keeps things cool when the music gets loud. Built for daily abuse and engineered for clean excursion, the HZS combines strength, efficiency, and low-profile fitment into one aggressive package. It’s the ideal solution when you want true bass performance without giving up precious install depth. Key Features: RMS Power : 600W Voice Coil : 2.5" black aluminum former - Dual 4Ω Cooling : Vented motor gap and solid pole piece Suspension : High-roll surround and progressive spider Lead Wires : Stitched mini-XL tinsel leads for long-term durability Motor Assembly : Bolt-through design for mechanical strength Mounting Depth : Compact profile for shallow, space-restricted enclosures Best Use : Ported enclosures for optimal output; sealed compatible

Sundown Audio HZS Series Subwoofers Purpose-Built for Tight Installs. Powered by Real Performance. The Sundown Audio HZS Series was engineered from the ground up to bring powerful, clean bass to space-limited installations—without sacrificing output, reliability, or thermal performance. Whether you’re working with a slim enclosure behind a truck seat, under a rear deck, or in a stealth build, the HZS delivers the kind of low-end impact you expect from Sundown. Available in 10" and 12" sizes, the HZS is a shallow-mount subwoofer rated for 600 watts RMS and designed to thrive in ported enclosures, though sealed options are also supported. Each model features a 2.5" black aluminum voice coil, a high-roll surround, a progressive spider, and a vented motor design that keeps things cool when the music gets loud. Built for daily abuse and engineered for clean excursion, the HZS combines strength, efficiency, and low-profile fitment into one aggressive package. It’s the ideal solution when you want true bass performance without giving up precious install depth. Key Features: RMS Power : 600W Voice Coil : 2.5" black aluminum former - Dual 4Ω Cooling : Vented motor gap and solid pole piece Suspension : High-roll surround and progressive spider Lead Wires : Stitched mini-XL tinsel leads for long-term durability Motor Assembly : Bolt-through design for mechanical strength Mounting Depth : Compact profile for shallow, space-restricted enclosures Best Use : Ported enclosures for optimal output; sealed compatible

•    RMS 300 watts•    Dual 4-ohm voice coils•    Optimized for small, ported enclosures•    Class-leading 14mm Xmax•    Double-stacked magnet•    Vented coil gap & pole for superior cooling•    Extra thick stamped steel frame•    High temp 4-layer copper voice coil•    High-quality push terminals•    Stitched-on flat tinsel leads•    Extremely low resonant frequency (Fs) Find the ideal balance of power, deep bass, and affordability with Sundown LCS subs. Sundown LCS woofers are known for their impressive bass response and high dependability. Typical entry-level woofers are limited in terms of excursion, mechanical ruggedness, and thermal performance. The v.2 update added an all-new, custom-tooled frame, push terminals, a rubber mounting gasket, and upgraded tinsel leads.  Physical Dimensions LCS V.2 10" / 12" T/S SPECS LCS V.2 10″D4 LCS V.2 12″D4 RE (Ohms) 7.140 6.9 FS (Hz) 34.642 33.442 VAS (L) 27.182 52.522 Qes 0.500 0.548 Qms 3.377 3.684 Qts 0.436 0.477 Le (mH) coming soon... 3.15 BL (NA) 19.313 20.073 Mms (Grams) 120.124 152.328 Cms (uM/N) 175.713 14.869 Sens (dB @ 1w/1m) 85.4 87.4 Xmax 14mm 14mm

•    500 Watts RMS / 1000 Watts Peak•    Dual 4-ohm voice coils•    Optimized for small, ported enclosures•    Class-leading 14mm Xmax•    Double-stacked magnet•    Vented coil gap & pole for superior cooling•    Extra thick stamped steel frame•    High temp 4-layer copper voice coil•    High-quality push terminals•    Stitched-on flat tinsel leads•    Extremely low resonant frequency (Fs) Find the ideal balance of power, deep bass, and affordability with Sundown LCS subs. Sundown LCS woofers are known for their impressive bass response and high dependability. Typical entry-level woofers are limited in terms of excursion, mechanical ruggedness, and thermal performance. The v.2 update added an all-new, custom-tooled frame, push terminals, a rubber mounting gasket, and upgraded tinsel leads.  Physical Dimensions LCS V.2 10" / 12" T/S SPECS LCS V.2 10″D4 LCS V.2 12″D4 RE (Ohms) 7.140 6.9 FS (Hz) 34.642 33.442 VAS (L) 27.182 52.522 Qes 0.500 0.548 Qms 3.377 3.684 Qts 0.436 0.477 Le (mH) coming soon... 3.15 BL (NA) 19.313 20.073 Mms (Grams) 120.124 152.328 Cms (uM/N) 175.713 14.869 Sens (dB @ 1w/1m) 85.4 87.4 Xmax 14mm 14mm

•    RMS 300 watts•    Dual 4-ohm voice coils•    Optimized for small, ported enclosures•    Class-leading 14mm Xmax•    Double-stacked magnet•    Vented coil gap & pole for superior cooling•    Extra thick stamped steel frame•    High temp 4-layer copper voice coil•    High-quality push terminals•    Stitched-on flat tinsel leads•    Extremely low resonant frequency (Fs) When it comes to the perfect combination of power, deep bass, and affordability, look no further than the Sundown LCS subs. As the creators of the loudest subs on Earth, Sundown knows bass best! The Sundown LCS woofers are known for their impressive bass response and high dependability. Typical entry-level woofers are limited in terms of excursion, mechanical ruggedness, and thermal performance. The v.2 update added an all-new, custom-tooled frame, push terminals, a rubber mounting gasket, and upgraded tinsel leads.   Physical Dimensions LCS V.2 10" / 12" T/S SPECS LCS V.2 10″D4 LCS V.2 12″D4 RE (Ohms) 7.140 6.9 FS (Hz) 34.642 33.442 VAS (L) 27.182 52.522 Qes 0.500 0.548 Qms 3.377 3.684 Qts 0.436 0.477 Le (mH) coming soon... 3.15 BL (NA) 19.313 20.073 Mms (Grams) 120.124 152.328 Cms (uM/N) 175.713 14.869 Sens (dB @ 1w/1m) 85.4 87.4 Xmax 14mm 14mm

• 500 Watts RMS / 1000 Watts Peak • Dual 4-ohm voice coils • Optimized for small, ported enclosures • Class-leading 14mm Xmax • Double-stacked magnet • Vented coil gap & pole for superior cooling • Extra thick stamped steel frame • High temp 4-layer copper voice coil • High-quality push terminals • Stitched-on flat tinsel leads • Extremely low resonant frequency (Fs) Find the ideal balance of power, deep bass, and affordability with Sundown LCS subs. Sundown LCS woofers are known for their impressive bass response and high dependability. Typical entry-level woofers are limited in terms of excursion, mechanical ruggedness, and thermal performance. The v.2 update added an all-new, custom-tooled frame, push terminals, a rubber mounting gasket, and upgraded tinsel leads. LCS V.2 10" / 12"

• 500 Watts RMS / 1000 Watts Peak • Dual 4-ohm voice coils • Optimized for small, ported enclosures • Class-leading 14mm Xmax • Double-stacked magnet • Vented coil gap & pole for superior cooling • Extra thick stamped steel frame • High temp 4-layer copper voice coil • High-quality push terminals • Stitched-on flat tinsel leads • Extremely low resonant frequency (Fs) Find the ideal balance of power, deep bass, and affordability with Sundown LCS subs. Sundown LCS woofers are known for their impressive bass response and high dependability. Typical entry-level woofers are limited in terms of excursion, mechanical ruggedness, and thermal performance. The v.2 update added an all-new, custom-tooled frame, push terminals, a rubber mounting gasket, and upgraded tinsel leads. Physical Dimensions LCS V.2 10" / 12"

4000w Peak / 2000w RMS Available in Dual 1 and Dual 2 Ohm Configurations Mega Roll Surround and Frame Etched All Black Backplate Quad Stack Magnet Structure   Specifications RE (Ohms) 2.27 4.19 FS (Hz) 37.825 37.736 VAS (L) 7.669 7.793 Qes 0.789 0.761 Qms 4.931 4.847 Qts 0.68 0.658 Le (mH) 1.887 3.682 BL (NA) 17.339 23.82 Mms (Grams) 439.5005 434.5335 Cms (uM/N) 40.281 40.935 Sens (dB @ 1w/1m) 78.95 79.14 Xmax 35mm 35mm T/S SPECS M10D1 M10D2 Enclosure Specifications Sealed Enclosure Not Recommended Ported Enclosure 1.5 cu ft Recommended Tuning 32Hz Recommended Port Area 24 sq in 4th Order Sealed Side 0.75 cu ft 4th Order Ported Side 2.25 cu ft 4th Order Port Area 45 sq in 4th Order Port Length 8" Displacement 0.2 cu ft Depth 10.09″ Outside Diameter 11.65″ Cut-Out 10.01″ Physical Dimensions Download

2000 Watts RMS / 4000 Watts Peak Available in Dual 1 and Dual 2 Ohm Configurations Mega Roll Surround and Frame Etched All Black Backplate Quad Stack Magnet Structure The Sundown M-Series is an all-new "entry-level" subwoofer in our Mega series - all Mega series subwoofers (10,12,15,18) feature our custom tooled and patented frames (US Patent Numbers D691596, D691597, D691598, and D741841) and our Mega-Roll surround. When we say "entry-level" this is only by comparison to its big brothers in our own Mega line - X,Z,NS series and higher. The M series was built for intense bass with stellar low-frequency performance at industry-leading levels of low-distortion. It does this while looking amazing - with a new laser-etched back-plate design and special M-series magnet boot design. For the M-series we mate out Mega series frames to a quad stacked 200mm (7.87”) diameter motor structure with a total magnet stack height of 88mm (3.46”) featuring a hyper-extended pole and extreme clearances (allowing 59.5mm to mechanical bottom effectively making it bottomless - this is 4.68" peak-to-peak). At Sundown we always do things to the extreme so even our "entry" level M-series features a full 20mm thick top-plate to finish the efficient magnetic circuit. We did all of this while still optimizing the cost to offer the absolute best-value to our customers. This motor drives a 3" diameter 4-Layer Round Wire Aluminum Voice Coil wound on a thick aluminum former to incredible levels of excursion. The new coil in the M-series was developed for both the M and X v.4 series and features a very special winding (invented by Sundown for the X-8 series originally) that allows the best winding packing density in the gap for both the D1 and D2 options. This coil is so massive that it allows even our M-series to achieve a full 35mm one-way linear excursion. We are truly setting a new industry standard with the M-series. Based on Sundown's years of experience we've included our highly efficient high-stroke coil ventilation system developed for the X and Z series originally. The M-series features a high-velocity pole vent, a heavily vented magnetic gap through the back-plate, and our proprietary high-velocity cast-aluminum frame-base venting system. The M-series was designed from the ground-up to become the new standard in the low-frequency / small, ported box subwoofer category in this price range. Never before have we been able to offer such an incredible value in the Mega series. They will work in the same enclosure as our other Mega platform subwoofers, but the M-series also opens up the possibility for sealed and IB applications. This is something that was not well suited to any other previous Mega platform subwoofer. The M-series is really a different kind of woofer due to its incredibly linear suspension. They are designed for the LOWEST level of bass extension possible in a small enclosure while maintaining extremely low levels of distortion. This is all thanks to the Sundown Mega-Roll surround & proprietary Sundown PG linear suspension (fully computer optimized). As with most subwoofers from Sundown the M-series features a magnet inner-diameter aluminum shorting ring for superior inductive distortion performance as well. We are quite certain that the M-series will go down in car audio history as one of the best low-distortion subwoofers per-dollar of its time.

Pride Audio M Series modular subwoofer designed for deep, powerful bass with high power handling. High-temperature voice coil with powerful magnetic system. Made in Russia for competition SPL and demanding audio applications. Available in multiple sizes for various installation requirements.

Pride Audio M Series modular subwoofer designed for deep, powerful bass with high power handling. High-temperature voice coil with powerful magnetic system. Made in Russia for competition SPL and demanding audio applications. Available in multiple sizes for various installation requirements.

4000w Peak / 2000w RMS Available in Dual 1 and Dual 2 Ohm Configurations Mega Roll Surround and Frame Etched All Black Backplate Quad Stack Magnet Structure   Specifications RE (Ohms) 2.1 4.11 FS (Hz) 28.187 28.567 VAS (L) 43.142 43.385 Qes 0.72 0.705 Qms 5.232 5.233 Qts 0.633 0.622 Le (mH) 1.829 3.645 BL (NA) 17.006 23.7995 Mms (Grams) 558.9059 541.082 Cms (uM/N) 57.043 57.363 Sens (dB @ 1w/1m) 83.024 83.3097 Xmax 35mm 35mm T/S SPECS M15D1 M15D2 Enclosure Specifications Sealed Enclosure Not Recommended Ported Enclosure 4.25 cu ft Recommended Tuning 32Hz Recommended Port Area 68 sq in 4th Order Sealed Side 2.0 cu ft 4th Order Ported Side 6.0 cu ft 4th Order Port Area 120 sq in 4th Order Port Length 8" Displacement 0.23 cu ft Depth 12.06″ Outside Diameter 15.51″ Cut-Out 13.93″

2000 Watts RMS / 4000 Watts Peak Available in Dual 1 and Dual 2 Ohm Configurations Mega Roll Surround and Frame Etched All Black Backplate Quad Stack Magnet Structure The Sundown M-Series is an all-new "entry-level" subwoofer in our Mega series - all Mega series subwoofers (10,12,15,18) feature our custom tooled and patented frames (US Patent Numbers D691596, D691597, D691598, and D741841) and our Mega-Roll surround. When we say "entry-level" this is only by comparison to its big brothers in our own Mega line - X,Z,NS series and higher. The M series was built for intense bass with stellar low-frequency performance at industry-leading levels of low-distortion. It does this while looking amazing - with a new laser-etched back-plate design and special M-series magnet boot design. For the M-series we mate out Mega series frames to a quad stacked 200mm (7.87”) diameter motor structure with a total magnet stack height of 88mm (3.46”) featuring a hyper-extended pole and extreme clearances (allowing 59.5mm to mechanical bottom effectively making it bottomless - this is 4.68" peak-to-peak). At Sundown we always do things to the extreme so even our "entry" level M-series features a full 20mm thick top-plate to finish the efficient magnetic circuit. We did all of this while still optimizing the cost to offer the absolute best-value to our customers. This motor drives a 3" diameter 4-Layer Round Wire Aluminum Voice Coil wound on a thick aluminum former to incredible levels of excursion. The new coil in the M-series was developed for both the M and X v.4 series and features a very special winding (invented by Sundown for the X-8 series originally) that allows the best winding packing density in the gap for both the D1 and D2 options. This coil is so massive that it allows even our M-series to achieve a full 35mm one-way linear excursion. We are truly setting a new industry standard with the M-series. Based on Sundown's years of experience we've included our highly efficient high-stroke coil ventilation system developed for the X and Z series originally. The M-series features a high-velocity pole vent, a heavily vented magnetic gap through the back-plate, and our proprietary high-velocity cast-aluminum frame-base venting system. The M-series was designed from the ground-up to become the new standard in the low-frequency / small, ported box subwoofer category in this price range. Never before have we been able to offer such an incredible value in the Mega series. They will work in the same enclosure as our other Mega platform subwoofers, but the M-series also opens up the possibility for sealed and IB applications. This is something that was not well suited to any other previous Mega platform subwoofer. The M-series is really a different kind of woofer due to its incredibly linear suspension. They are designed for the LOWEST level of bass extension possible in a small enclosure while maintaining extremely low levels of distortion. This is all thanks to the Sundown Mega-Roll surround & proprietary Sundown PG linear suspension (fully computer optimized). As with most subwoofers from Sundown the M-series features a magnet inner-diameter aluminum shorting ring for superior inductive distortion performance as well. We are quite certain that the M-series will go down in car audio history as one of the best low-distortion subwoofers per-dollar of its time.

4000w Peak / 2000w RMS Available in Dual 1 and Dual 2 Ohm Configurations Mega Roll Surround and Frame Etched All Black Backplate Quad Stack Magnet Structure   Specifications RE (Ohms) 2.12 4.125 FS (Hz) 26.152 25.749 VAS (L) 112.182 117.53 Qes 0.782 0.74 Qms 5.452 5.379 Qts 0.684 0.65 Le (mH) 1.797 3.55 BL (NA) 17.044 24.026 Mms (Grams) 651.24 638.994 Cms (uM/N) 56.86 59.58 Sens (dB @ 1w/1m) 85.836 86.102 Xmax 35mm 35mm T/S SPECS M18D1 M18D2 Enclosure Specifications Sealed Enclosure Not Recommended Ported Enclosure 7.0 cu ft Recommended Tuning 32Hz Recommended Port Area 112 sq in 4th Order Sealed Side 3.0 cu ft 4th Order Ported Side 9.0 cu ft 4th Order Port Area 180 sq in 4th Order Port Length 8" Displacement 0.25 cu ft Depth 14.05″ Outside Diameter 18.46″ Cut-Out 16.68″

2000 Watts RMS / 4000 Watts Peak Available in Dual 1 and Dual 2 Ohm Configurations Mega Roll Surround and Frame Etched All Black Backplate Quad Stack Magnet Structure The Sundown M-Series is an all-new "entry-level" subwoofer in our Mega series - all Mega series subwoofers (10,12,15,18) feature our custom tooled and patented frames (US Patent Numbers D691596, D691597, D691598, and D741841) and our Mega-Roll surround. When we say "entry-level" this is only by comparison to its big brothers in our own Mega line - X,Z,NS series and higher. The M series was built for intense bass with stellar low-frequency performance at industry-leading levels of low-distortion. It does this while looking amazing - with a new laser-etched back-plate design and special M-series magnet boot design. For the M-series we mate out Mega series frames to a quad stacked 200mm (7.87”) diameter motor structure with a total magnet stack height of 88mm (3.46”) featuring a hyper-extended pole and extreme clearances (allowing 59.5mm to mechanical bottom effectively making it bottomless - this is 4.68" peak-to-peak). At Sundown we always do things to the extreme so even our "entry" level M-series features a full 20mm thick top-plate to finish the efficient magnetic circuit. We did all of this while still optimizing the cost to offer the absolute best-value to our customers. This motor drives a 3" diameter 4-Layer Round Wire Aluminum Voice Coil wound on a thick aluminum former to incredible levels of excursion. The new coil in the M-series was developed for both the M and X v.4 series and features a very special winding (invented by Sundown for the X-8 series originally) that allows the best winding packing density in the gap for both the D1 and D2 options. This coil is so massive that it allows even our M-series to achieve a full 35mm one-way linear excursion. We are truly setting a new industry standard with the M-series. Based on Sundown's years of experience we've included our highly efficient high-stroke coil ventilation system developed for the X and Z series originally. The M-series features a high-velocity pole vent, a heavily vented magnetic gap through the back-plate, and our proprietary high-velocity cast-aluminum frame-base venting system. The M-series was designed from the ground-up to become the new standard in the low-frequency / small, ported box subwoofer category in this price range. Never before have we been able to offer such an incredible value in the Mega series. They will work in the same enclosure as our other Mega platform subwoofers, but the M-series also opens up the possibility for sealed and IB applications. This is something that was not well suited to any other previous Mega platform subwoofer. The M-series is really a different kind of woofer due to its incredibly linear suspension. They are designed for the LOWEST level of bass extension possible in a small enclosure while maintaining extremely low levels of distortion. This is all thanks to the Sundown Mega-Roll surround & proprietary Sundown PG linear suspension (fully computer optimized). As with most subwoofers from Sundown the M-series features a magnet inner-diameter aluminum shorting ring for superior inductive distortion performance as well. We are quite certain that the M-series will go down in car audio history as one of the best low-distortion subwoofers per-dollar of its time.

3500 Watt RMS / 7000 Watt Peak Dual 1 or 2 ohm voice coils Optional carbon cone/dustcap available Custom tooled basket Custom-tooled ultra-linear spider packs Extended shorting ring Eight-layer voice coil Custom tooled basket Cast aluminum cooling ring Ultra-linear spider pack Unique air exchanging system forces hot air out and cool air in Aluminum vent ring Ultra-linear Mega Roll V2 surround Features: The Nightshade 3,000-watt Neodymium sub is engineered to deliver incredibly powerful low end, with an extremely linear excursion and next-level thermal management. It features an eight-layer voice coil for excellent power handling and an extended shorting ring to minimize distortion and deliver a smooth, highly accurate sound at extreme SPL levels. Thermal control is optimized with a cast aluminum cooling ring, outer fin array and aluminum vent ring to actively pull heat away from the entire voice coil gap. The subwoofer also incorporates a unique air exchange system for active cooling, enhancing reliability during extended use. With a Mega Roll V2 surround for linear cone movement and class-leading Xmax, the Nightshade is the premier high-performance Neodymium subwoofer in the category.

3500 Watt RMS / 7000 Watt Peak Dual 1 or 2 ohm voice coils Optional carbon cone/dustcap available Custom tooled basket Custom-tooled ultra-linear spider packs Extended shorting ring Eight-layer voice coil Custom tooled basket Cast aluminum cooling ring Ultra-linear spider pack Unique air exchanging system forces hot air out and cool air in Aluminum vent ring Ultra-linear Mega Roll V2 surround Features: The Nightshade 3,000-watt Neodymium sub is engineered to deliver incredibly powerful low end, with an extremely linear excursion and next-level thermal management. It features an eight-layer voice coil for excellent power handling and an extended shorting ring to minimize distortion and deliver a smooth, highly accurate sound at extreme SPL levels.

3500 Watt RMS / 7000 Watt Peak Dual 1 or 2 ohm voice coils Optional carbon cone/dustcap available Custom tooled basket Custom-tooled ultra-linear spider packs Extended shorting ring Eight-layer voice coil Custom tooled basket Cast aluminum cooling ring Ultra-linear spider pack Unique air exchanging system forces hot air out and cool air in Aluminum vent ring Ultra-linear Mega Roll V2 surround Features: The Nightshade 3,000-watt Neodymium sub is engineered to deliver incredibly powerful low end, with an extremely linear excursion and next-level thermal management. It features an eight-layer voice coil for excellent power handling and an extended shorting ring to minimize distortion and deliver a smooth, highly accurate sound at extreme SPL levels.

3500 Watt RMS / 7000 Watt Peak Dual 1 or 2 ohm voice coils Optional carbon cone/dustcap available Custom tooled basket Custom-tooled ultra-linear spider packs Extended shorting ring Eight-layer voice coil Custom tooled basket Cast aluminum cooling ring Ultra-linear spider pack Unique air exchanging system forces hot air out and cool air in Aluminum vent ring Ultra-linear Mega Roll V2 surround The Nightshade 3,000-watt Neodymium sub is engineered to deliver incredibly powerful low end, with an extremely linear excursion and next-level thermal management. It features an eight-layer voice coil for excellent power handling and an extended shorting ring to minimize distortion and deliver a smooth, highly accurate sound at extreme SPL levels.

PSE-8 Freq. range 20hz-150hz FS 43hz Xmax 12mm D4 250W RMS Mounting depth 4.75” Cutout 7.5”

PSE-8 Freq. range 20hz-150hz FS 43hz Xmax 12mm D4 250W RMS Mounting depth 4.75” Cutout 7.5”  

These are standard drop-in recone kits ONLY. There are no refunds or exchanges with drop-in re-cone kits. Please make sure you are ordering the correct model, version and impedance prior to ordering.

coming soon

These are standard drop-in recone kits ONLY. There are no refunds or exchanges with drop-in re-cone kits. Please make sure you are ordering the correct model, version and impedance prior to ordering.

coming soon

coming soon

These are standard drop-in recone kits ONLY. There are no refunds or exchanges with drop-in re-cone kits. Please make sure you are ordering the correct model, version and impedance prior to ordering.

These are standard drop-in recone kits ONLY. There are no refunds or exchanges with drop-in re-cone kits. Please make sure you are ordering the correct model, version and impedance prior to ordering.

coming soon

Coming Soon...

coming soon

coming soon

1000 Watt RMS/ 2000 Watt Peak Dual 2 or 4 ohm voice coils Optimized for small ported, sealed, & band-pass enclosures Large aluminum Faraday ring for smooth acoustic response High strength cast aluminum frame Low distortion motor construction High-temperature voice coil wire Spring-loaded terminals Stitched-on “XL” tinsel lead wires The SA Classic sub is the perfect combination of power handling and deep excursion. A cast aluminum frame houses a bulletproof custom 2.5-inch voice coil, robust double-layered Nomex spider, and SPL competition-grade paper cone, all built into a flexible design that works in any kind of enclosure.

1000 Watt RMS/ 2000 Watt Peak Dual 2 or 4 ohm voice coils Optimized for small ported, sealed, & band-pass enclosures Large aluminum Faraday ring for smooth acoustic response High strength cast aluminum frame Low distortion motor construction High-temperature voice coil wire Spring-loaded terminals Stitched-on “XL” tinsel lead wires   The SA Classic sub is the perfect combination of power handling and deep excursion. A cast aluminum frame houses a bulletproof custom 2.5-inch voice coil, robust double-layered Nomex spider, and SPL competition-grade paper cone, all built into a flexible design that works in any kind of enclosure. Specifications RE (Ohms) 4.29 7.08 FS (Hz) 35.4 36.6 VAS (L) 10.13 10.66 Qes 0.52 0.54 Qms 5.41 5.30 Qts 0.48 0.49 Le (mH) 3.41 4.71 BL (NA) 20.40 24.82 Mms (Grams) 230 205 Cms (uM/N) 87.8 92.4 Sens (dB @ 1w/1m) 81.0 81.6 Xmax 19mm 19mm T/S SPECS SA CLASSIC 10" D2 SA CLASSIC 10" D4 Enclosure Specifications SA CLASSIC 10" Sealed Enclosure 0.5 cu ft Ported Enclosure 1.0 cu ft Recommended Tuning 35Hz Recommended Port Area 15 sq in Displacement 0.1 cu ft Depth 6″ Outside Diameter 10.5″ Cut-Out 9.25″ Physical Dimensions Download Enclosure Designs .Zip File

1000 Watt RMS/ 2000 Watt Peak Dual 2 or 4 ohm voice coils Optimized for small ported, sealed, & band-pass enclosures Large aluminum Faraday ring for smooth acoustic response High strength cast aluminum frame Low distortion motor construction High-temperature voice coil wire Spring-loaded terminals Stitched-on “XL” tinsel lead wires The SA Classic sub is a stunning combination of value, power handling, and deep excursion. It features a cast aluminum frame that houses a bulletproof custom 2.5-inch voice coil, robust double-layered Nomex spider, and SPL competition-grade paper cone. These components are built into a flexible design that works well in any type of enclosure. Specifications T/S SPECS SA CLASSIC 12" D2 SA CLASSIC 12" D4 RE (Ohms) 4.57 7.07 FS (Hz) 33.71 33.96 VAS (L) 21.21 24.63 Qes 0.58 0.55 Qms 5.34 5.15 Qts 0.52 0.49 Le (mH) 3.40 4.84 BL (NA) 21.64 25.67 Mms (Grams) 280 237 Cms (uM/N) 79.43 92.27 Sens (dB @ 1w/1m) 83.21 84.22 Xmax 19mm 19mm Enclosure Specifications SA CLASSIC 12" Sealed Enclosure 1.0 cu ft Ported Enclosure 1.75 cu ft Recommended Tuning 35Hz Recommended Port Area 26 sq in Displacement 0.14 cu ft Depth 6.5″ Outside Diameter 12.625″ Cut-Out 11.125″ Physical Dimensions Download Enclosure Designs .Zip File

  Here at Sundown Audio we take feedback from customers and dealers seriously. With the launch of the SA v.2 woofers we heard a lot of call to also keep the old version for lower depth / lower cost applications — so we did that via the “Classic” SA. Still available in 10's, 12's and 15's, it is essentially the SA v.1 Rev.3 but with a black motor finish. We even squeezed in an upgrade… the motor is bolted together for enhanced long-term durability! The Sundown SA series has been our most popular product line since the introduction of the SA-12 in 2009. It was the result of over a year of testing and prototyping until all of our goals and expectations were blown away. The SA series has continually evolved over the years thanks to extensive testing and feedback from our SPL competition Team and our customers but still stays true to its legendary design heritage. It has never failed to prove itself year-in and year-out in every application ranging from daily musical builds to all-out SPL competition vehicles. When designing the SA series we started out with an FEA optimized motor & coil design capable of 19mm of one-way Klippel verified excursion and just over 33mm of x-mech. This motor & coil setup was then mated up to an extremely robust double-layer Nomex spider with fully tied-on “XL” tinsel leads (84-Strands of Conductor), an SPL competition grade paper cone, and a strong foam surround. The motor also features a large magnet ID shorting ring (faraday ring) to reduce distortion causes by inductance & inductance variation over stroke. Features Xmax = 19mm one-way by 70% BL RMS Power = 750-watts Vented magnetic gap Optimized high-velocity pole vent Innovative high-velocity vented frame spacer ring Black Aluminum 2.5” voice coil former for superior heat dissipation High Temperature copper voice coil wire Large aluminum faraday ring (Magnet ID) Spring Loaded Terminals Stitched-On “XL” Tinsel Leads to prevent fatigue and failure High strength cast alum

1000 Watt RMS/ 2000 Watt Peak Dual 2 or 4 ohm voice coils Optimized for small ported, sealed, & band-pass enclosures Large aluminum Faraday ring for smooth acoustic response High strength cast aluminum frame Low distortion motor construction High-temperature voice coil wire Spring-loaded terminals Stitched-on “XL” tinsel lead wires The SA Classic sub is a stunning combination of value, power handling, and deep excursion. It features a cast aluminum frame that houses a bulletproof custom 2.5-inch voice coil, robust double-layered Nomex spider, and SPL competition-grade paper cone. These components are built into a flexible design that works well in any type of enclosure.   Specifications RE (Ohms) 4.29 7.00 FS (Hz) 37.8 36.4 VAS (L) 55.4 67.3 Qes 0.55 0.62 Qms 2.86 2.94 Qts 0.46 0.51 Le (mH) 3.41 4.71 BL (NA) 23.4 26.94 Mms (Grams) 319 284 Cms (uM/N) 55.3 67.2 Sens (dB @ 1w/1m) 89.2 89.0 Xmax 19mm 19mm T/S SPECS SA CLASSIC 15" D2 SA CLASSIC 15" D4 Enclosure Specifications Sealed Enclosure 2.5 cu ft Ported Enclosure 3.5 cu ft Recommended Tuning 35Hz Recommended Port Area 35 sq in Displacement 0.17 cu ft Depth 7.69″ Outside Diameter 15.5″ Cut-Out 14″ Physical Dimensions Download

300 Watts RMS/ 600 Watts Peak Dual 2 or 4 ohm voice coils Large aluminum Faraday ring for smooth acoustic response High-temperature voice coil wire Spring-loaded terminals Integrated vent channels for enhanced cooling Perfect for under/behind seat sub enclosures The SA-6.5SW was created to achieve extremely high performance with less than 4” of mounting depth. Sundown uses a solid-pole design, allowing the back plate to rest against the back wall of the enclosure to reduce the mounting depth requirements even more. Twenty millimeters of mechanical excursion means surprisingly deep bass out of this mighty 6.5” sub!

1250 Watts RMS / 2500 Watts Peak Dual 2 or 4 ohm voice coils Vented magnetic gap & pole piece Aluminum 2.75” voice coil former for superior heat dissipation Innovative high velocity, cast aluminum vented frame spacer ring Magnet ID faraday ring for smooth acoustic response High-temperature copper voice coil wire Spring-loaded terminals Stitched-on double “XL” tinsel leads This SA-10/12/15 v.2 series is a top-down upgrade from the original SA series. The 2.75” coil punches way above its weight, outperforming many 3” coils without the adding weight & with the added advantage of a wider spider. We are able to perfectly balance the mass, motor force, and suspension stiffness for the intended power level. The motor also features a large magnet shorting ring (faraday ring) to reduce distortion and deliver smoother response across the entire acoustic spectrum. The motor & coil setup is mated to an extremely robust multi-layer spider with fully tied-on & doubled-up “XL” tinsel leads. A competition-grade paper cone, strong foam surround, and cast aluminum frame are used to complete this masterpiece. On top of the ~19mm of one-way linear excursion we have an x-mech limit of 37mm one-way before coil bottom making it nearly "bottomless." The 18" model features a larger diameter motor to drive the higher mass.

RMS 200 watts Dual 2 or 4 ohm voice coils Large aluminum Faraday ring for smooth acoustic response High-temperature voice coil wire Spring-loaded terminals Integrated vent channels for enhanced cooling Perfect for under/behind seat sub enclosures The SA-6.5SW was created to achieve extremely high performance with less than 4” of mounting depth. Sundown uses a solid-pole design, allowing the back plate to rest against the back wall of the enclosure to reduce the mounting depth requirements even more. Twenty millimeters of mechanical excursion means surprisingly deep bass out of this mighty 6.5” sub! Specifications RE (Ohms) 4.0 7.1 FS (Hz) 48.9 51.8 VAS (L) 4.1 3.6 Qes 0.50 0.54 Qms 4.82 4.65 Qts 0.46 0.49 Le (mH) 1.69 2.45 BL (NA) 13.5 17.9 Mms (Grams) 74.8 75.6 Cms (uM/N) .14 .12 Sens (dB @ 1w/1m) 81.6 81.5 Xmax 10mm 10mm T/S SPECS SA 6.5 D2 SA 6.5 D4 Enclosure Specifications Sealed Enclosure 0.15 cu ft Ported Enclosure 0.3 cu ft Recommended Tuning 40Hz Recommended Port Area 4 sq in Displacement Depth 3.79" Outside Diameter 7.16″ Cut-Out 5.93″ Physical Dimensions Download

RMS 1250 watts Dual 2 or 4 ohm voice coilsSpecifications RE (Ohms)3.46.06FS (Hz)3636VAS (L)10.2868.497Qes0.5010.509Qms2.3412.445Qts0.4130.421Le (mH)3.5174.456BL (NA)22.26731.742Mms (Grams)304.447337.651Cms (uM/N)57.02447.126Sens (dB @ 1w/1m)82.582.1Xmax22mm22mmT/S SPECSSAV3 10″ D2SAV3 10″ D4Enclosure Specifications Sealed Enclosure0.5 cu ftPorted Enclosure1.0 cu ftRecommended Tuning35HzRecommended Port Area15 sq inDisplacement.17 cu ftDepth6.92"Outside Diameter11″Cut-Out9.5″Physical DimensionsDownloadEnclosure Designs .Zip File

RMS 1250 watts Dual 2 or 4 ohm voice coilsSpecifications RE (Ohms)3.046.06FS (Hz)3535VAS (L)22.18819.22Qes0.5250.516Qms2.3082.396Qts0.4280.424Le (mH)3.17854.6357BL (NA)22.9932.182Mms (Grams)369.747372.752Cms (uM/N)55.43148.017Sens (dB @ 1w/1m)84.0584.9Xmax22mm22mmT/S SPECSSAV3 12″ D2SAV3 12″ D4Enclosure Specifications Sealed Enclosure1.0 cu ftPorted Enclosure1.75 cu ftRecommended Tuning35HzRecommended Port Area26 sq inDisplacement.18 cu ftDepth8.4"Outside Diameter12.84″Cut-Out11.2″Physical DimensionsDownloadEnclosure Designs .Zip File

1500 Watts / 3000 Watts Peak Dual 2 or 4 ohm voice coils Enclosure Specifications Sealed Enclosure 2.0 cu ft Ported Enclosure 3.0 cu ft Recommended Tuning 35Hz Recommended Port Area 44 sq in Displacement Depth 8.65" Outside Diameter 15.59″ Cut-Out 14.01″ Physical Dimensions Download Enclosure Designs .Zip File

600 Watts RMS/1200 Watts Peak Dual 2 or 4 ohm voice coils Vented magnetic gap with 16 chamfered vents Large aluminum Faraday ring for smooth acoustic response Patented high-strength cast aluminum frame Low distortion motor construction High-temperature voice coil wire Spring-loaded terminals Stitched-on “XL” tinsel lead wires The pinnacle of low distortion ported box subwoofer technology, the SA 8-inch sub is completely custom tooled. It has a full 16mm of one-way linear excursion and mechanical capacity, exceeding double the linear limits, ensuring durability and low distortion. The  v.3 update includes a new surround with linear geometry and improved thermal performance with the addition of 16 chamfered gap vents to keep high-velocity air flowing over the voice coil. SA V.3 8" RE (Ohms) 3.36 6.0 FS (Hz) 38.29 40.0 VAS (L) 6.88 7.17 Qes 0.324 0.392 Qms 6.31 4.31 Qts 0.309 0.36 Le (mH) 2.08 3.32 BL (NA) 18.94 22.06 Mms (Grams) 144 126.6 Cms (uM/N) 120 125 Sens (dB @ 1w/1m) 82.79 82.71 Xmax 16mm 16mm T/S SPECS SAV3 8″ D2 SAV3 8″ D4 SA V.3 8" Sealed Enclosure 0.3 cu ft Ported Enclosure 0.65 cu ft Recommended Tuning 35Hz Recommended Port Area 9 sq in Displacement 0.08 cu ft Depth 6.625″ Outside Diameter 8.629″ Cut-Out 7.375″ Physical Dimensions Download

RMS 600 watts Dual 2 or 4 ohm voice coils Optimized for small, sealed enclosures Lightweight Neodymium motor Computer-optimized foam “w” surround Two-inch 8-layer copper voice coil Large aluminum Faraday ring for smooth acoustic response Patented high strength cast aluminum frame Low distortion motor construction High-temperature voice coil wire Spring-loaded terminals Stitched-on tinsel lead wires The SD-4 series truly is a world-class sound quality woofer with low mounting depth, small box requirements, yet extraordinarily high power handling. It's the ideal choice for anyone seeking a high-quality, low-mounting-depth subwoofer that performs hammers in small enclosures. With enhanced mechanical durability and superb sound quality, you get the perfect marriage of form and function.

RMS 600 watts Dual 2 or 4 ohm voice coils Optimized for small, sealed enclosures Lightweight Neodymium motor Computer-optimized foam “w” surround Two-inch 8-layer copper voice coil Large aluminum Faraday ring for smooth acoustic response Patented high strength cast aluminum frame Low distortion motor construction High-temperature voice coil wire Spring-loaded terminals Stitched-on tinsel lead wires The SD-4 series truly is a world-class sound quality woofer with low mounting depth, small box requirements, yet extraordinarily high power handling. It's the ideal choice for anyone seeking a high-quality, low-mounting-depth subwoofer that performs hammers in small enclosures. With enhanced mechanical durability and superb sound quality, you get the perfect marriage of form and function.

RMS 400 watts Dual 2 or 4 ohm voice coils Optimized for small, sealed enclosures Lightweight Neodymium motor Computer-optimized foam “w” surround Two-inch 8-layer copper voice coil Large aluminum Faraday ring for smooth acoustic response Patented high strength cast aluminum frame Low distortion motor construction High-temperature voice coil wire Spring-loaded terminals Stitched-on tinsel lead wires The SD-4 series truly is a world-class sound quality woofer with low mounting depth, small box requirements, yet extraordinarily high power handling. It's the ideal choice for anyone seeking a high-quality, low-mounting-depth subwoofer that performs hammers in small enclosures. With enhanced mechanical durability and superb sound quality, you get the perfect marriage of form and function.

3,500 watts RMS Available in 10 through 18-inch versions Dual 1 ohm coils Mega V2 Cone Aluminum 3.3” x 80mm coil Dual 8 AWG terminals with dual-layer tinsel leads Custom cross-cut pole piece with Neodymium cap for increased output and thermal control 5-layer spider 1,336 oz (83.5 lbs) magnet with integrated thermal ventilation Optimized for Ported & 6th order enclosures Carbon cone upgrade available Designed in-house by Sundown Founder Jacob Fuller, the 3,500-watt RMS SDDN is available in 10, 12, 15, and 18-inch models. Each unit boasts a massive 83-pound motor with integrated thermal ventilation, featuring a custom cross-cut pole piece with a Neodymium cap for increased output and thermal control. Sundown’s signature Mega V2 cone is paired with a five-layer spider, a 3.3” x 80mm aluminum voice coil (dual 1-ohm), and dual tinsel leads per eight-gauge terminal.

3,500 watts RMS Available in 10 through 18-inch versions Dual 1 ohm coils Mega V2 Cone Aluminum 3.3” x 80mm coil Dual 8 AWG terminals with dual-layer tinsel leads Custom cross-cut pole piece with Neodymium cap for increased output and thermal control 5-layer spider 1,336 oz (83.5 lbs) magnet with integrated thermal ventilation Optimized for Ported & 6th order enclosures Carbon cone upgrade available Designed in-house by Sundown Founder Jacob Fuller, the 3,500-watt RMS SDDN is available in 10, 12, 15, and 18-inch models. Each unit boasts a massive 83-pound motor with integrated thermal ventilation, featuring a custom cross-cut pole piece with a Neodymium cap for increased output and thermal control. Sundown’s signature Mega V2 cone is paired with a five-layer spider, a 3.3” x 80mm aluminum voice coil (dual 1-ohm), and dual tinsel leads per eight-gauge terminal.

3,500 watts RMS Available in 10 through 18-inch versions Dual 1 ohm coils Mega V2 Cone Aluminum 3.3” x 80mm coil Dual 8 AWG terminals with dual-layer tinsel leads Custom cross-cut pole piece with Neodymium cap for increased output and thermal control 5-layer spider 1,336 oz (83.5 lbs) magnet with integrated thermal ventilation Optimized for Ported & 6th order enclosures Carbon cone upgrade available Designed in-house by Sundown Founder Jacob Fuller, the 3,500-watt RMS SDDN is available in 10, 12, 15, and 18-inch models. Each unit boasts a massive 83-pound motor with integrated thermal ventilation, featuring a custom cross-cut pole piece with a Neodymium cap for increased output and thermal control. Sundown’s signature Mega V2 cone is paired with a five-layer spider, a 3.3” x 80mm aluminum voice coil (dual 1-ohm), and dual tinsel leads per eight-gauge terminal.

3,500 watts RMS Available in 10 through 18-inch versions Dual 1 ohm coils Mega V2 Cone Aluminum 3.3” x 80mm coil Dual 8 AWG terminals with dual-layer tinsel leads Custom cross-cut pole piece with Neodymium cap for increased output and thermal control 5-layer spider 1,336 oz (83.5 lbs) magnet with integrated thermal ventilation Optimized for Ported & 6th order enclosures Carbon cone upgrade available Designed in-house by Sundown Founder Jacob Fuller, the 3,500-watt RMS SDDN is available in 10, 12, 15, and 18-inch models. Each unit boasts a massive 83-pound motor with integrated thermal ventilation, featuring a custom cross-cut pole piece with a Neodymium cap for increased output and thermal control. Sundown’s signature Mega V2 cone is paired with a five-layer spider, a 3.3” x 80mm aluminum voice coil (dual 1-ohm), and dual tinsel leads per eight-gauge terminal.

600 Watts RMS/1200 Watts Peak Dual 2 or 4 ohm voice coils Black Aluminum 2.5” voice coil for superior heat dissipation High-temperature 4-layer copper voice coil wire Stitched-on “Mini-XL” tinsel leads to prevent fatigue and failure Solid pole-piece and multi-vent magnetic gap Dual-magnet design for smooth acoustic response Custom tooled cone shape for reduced mechanical noise over high excursion Bolt-through motor design to ensure maximum longevity and ruggedness Sundown’s highest-power slim subwoofers, the SLD takes incredibly high volume by introducing numerous important upgrades: pole-piece channels for reduced air noise & increased cooling, top-plate “slits” for better cooling and less distortion, and a magnet shorting ring. Sundown also bolted down the spider, bolted the motor together, bolted on the aluminum pole cap, and added “mini-XL” lead wires for years of flawless service.

600 Watts RMS/1200 Watts Peak Dual 2 or 4 ohm voice coils Black Aluminum 2.5” voice coil for superior heat dissipation High-temperature 4-layer copper voice coil wire Stitched-on “Mini-XL” tinsel leads to prevent fatigue and failure Solid pole-piece and multi-vent magnetic gap Dual-magnet design for smooth acoustic response Custom tooled cone shape for reduced mechanical noise over high excursion Bolt-through motor design to ensure maximum longevity and ruggedness Sundown's SLD slim subwoofers deliver incredibly high volume through several important upgrades. These include pole-piece channels to reduce air noise and improve cooling, top-plate "slits" for better cooling and less distortion and a magnet shorting ring. Sundown has also secured the spider, motor, and aluminum pole cap with bolts, and added "mini-XL" lead wires for years of reliable service.

600 Watts RMS/1200 Watts Peak Dual 2 or 4 ohm voice coils Black Aluminum 2.5” voice coil former for superior heat dissipation High temperature 4-layer copper voice coil wire Stitched-on “Mini-XL” tinsel Leads to prevent fatigue and failure Vented pole-piece and vented magnetic gap Dual-magnet design for smooth acoustic response Custom tooled cone shape for reduced mechanical noise over high excursion Bolt-through motor design to ensure maximum longevity and ruggedness The SML series is a revolutionary line of subwoofers offered by Sundown Audio. An inch shallower than our SLD series, it delivers nearly the excursion, making it an ideal choice for customers seeking an extremely shallow driver with deep bass. Designed to fit under or behind your seat, the SML series performs exceptionally well in small enclosures.

600 Watts RMS/1200 Watts Peak Dual 2 or 4 ohm voice coils Black Aluminum 2.5” voice coil former for superior heat dissipation High temperature 4-layer copper voice coil wire Stitched-on “Mini-XL” tinsel leads to prevent fatigue and failure Vented pole-piece and multi-vented magnetic gap Dual-magnet design for smooth acoustic response Custom tooled cone shape for reduced mechanical noise over high excursion Bolt-through motor design to ensure maximum longevity and ruggedness Introducing the SML series: a revolutionary line of subwoofers by Sundown Audio. This series is an inch shallower than the SLD line, yet delivers nearly the same excursion, making it the ultimate choice for customers in search of an extremely shallow driver with deep bass. Specifically designed to fit under or behind your seat, the SML series excels in performance, especially within small enclosures.

RMS 300 watts Dual 2 or 4 ohm voice coils Black Aluminum 2.25” voice coil former for superior heat dissipation High temperature 4-layer copper voice coil wire Stitched-on “Mini-XL” tinsel Leads to prevent fatigue and failure Vented pole-piece and vented magnetic gap Dual-magnet design for smooth acoustic response Custom tooled cone shape for reduced mechanical noise over high excursion Bolt-through motor design to ensure maximum longevity and ruggedness  The SML series is a revolutionary line of subwoofers offered by Sundown Audio. An inch shallower than our SLD series, it delivers nearly the excursion, making it an ideal choice for customers seeking an extremely shallow driver with deep bass. Designed to fit under or behind your seat, the SML series performs exceptionally well in small enclosures. Specifications T/S SPECS SML 8" D2 SML 8" D4 RE (Ohms) 3.65 6.85 FS (Hz) 40.038 43.25 VAS (L) 8.028 7.246 Qes 0.425 0.512 Qms 2.75 2.796 Qts 0.368 0.432 BL (NA) 16.634 21.266 Mms (Grams) 128.033 124.288 Cms (uM/N) 123.416 108.954 Sens (dB @ 1w/1m) 82.8dB 82.5dB Xmax 14mm 14mm Enclosure Specifications   SML 8" Sealed Enclosure 0.2-0.35 ft^3 Displacement 0.08cuft Cutout 7.65" Outer Diameter  8.5"   Mounting Depth 3.78” Physical Dimensions Download

RMS 300 watts Dual 2 or 4 ohm voice coils Black Aluminum 2.25” voice coil former for superior heat dissipation High temperature 4-layer copper voice coil wire Stitched-on “Mini-XL” tinsel Leads to prevent fatigue and failure Vented pole-piece and vented magnetic gap Dual-magnet design for smooth acoustic response Custom tooled cone shape for reduced mechanical noise over high excursion Bolt-through motor design to ensure maximum longevity and ruggedness The SML series is a revolutionary line of subwoofers offered by Sundown Audio. An inch shallower than our SLD series, it delivers nearly the excursion, making it an ideal choice for customers seeking an extremely shallow driver with deep bass. Designed to fit under or behind your seat, the SML series performs exceptionally well in small enclosures.Specifications T/S SPECSSML 8" D2SML 8" D4RE (Ohms)3.656.85FS (Hz)40.03843.25VAS (L)8.0287.246Qes0.4250.512Qms2.752.796Qts0.3680.432BL (NA)16.63421.266Mms (Grams)128.033124.288Cms (uM/N)123.416108.954Sens (dB @ 1w/1m)82.8dB82.5dBXmax14mm14mm Enclosure Specifications SML 8"Sealed Enclosure0.2-0.35 ft^3Displacement0.08cuftCutout7.65"Outer Diameter 8.5"Mounting Depth3.78”Physical DimensionsDownload

SUNDOWN AUDIO E Series v.3 15 D2 Subwoofer: Since their introduction in 2012 the Sundown E series woofers have been known for their impressive bass response and high levels of dependability. Typical entry level woofers are highly limited in terms of linear excursion, mechanical ruggedness, and thermal performance – these are all aspects that we have taken to the next level in the Sundown E series. A double stacked magnet structure and an extremely long voice coil allow us to achieve a class-leading linear x-max of 14mm one-way in addition to high mechanical clearances (over 2” peak-to-peak). The large coil combined with gap venting, a vented voice coil former, and chamfered pole-piece design give the E Series impressive thermal performance. Mechanical stability and durability are addressed via the extremely strong competition-grade paper cone, rugged and over-sized foam surround, and a high quality spider with fully tied-on tinsel leads. All major areas of woofer durability have been addressed to the maximum level possible in this category. Bottom-line; if you are looking for a great subwoofer option and do not want to break the bank the Sundown E-Series woofers are for you. They are ideal for anyone from beginners to seasoned professionals seeking industry leading performance at a value price point.Features & Technology: Xmax = 14mm one-way by 70% BL RMS Power = 500-watts Vented magnetic gap Solid Pole piece with chamfered edges for increased air powered voice coil cooling Black Aluminum 2” voice coil former for superior heat dissipation High Temperature copper voice coil wire Spring Loaded Terminals Stitched-On Tinsel Leads to prevent fatigue and fa

500 Watts RMS/1000 Watts Peak Dual 2 or 4 ohm voice coils Optimized for small ported enclosures Aluminum 1.75” voice coil former for superior heat dissipation High-temperature copper voice coil Double stitched surround Heavy-duty cast basket Spring-loaded terminals accept up to 8-gauge wire Stitched-on heavy-duty tinsel leads Solid pole with vent channels and aluminum shorting ring cap Rear gap-venting Top-Plate Cooling Channels

750W Watts RMS / 1500 Watts Peak Dual 2 or 4 ohm voice coils Optimized for small ported enclosures Aluminum 2.25” voice coil former for superior heat dissipation High-temperature copper voice coil Double stitched surround Heavy-duty cast basket Spring-loaded terminals accept up to 8-gauge wire Stitched-on heavy-duty tinsel leads Solid pole with vent channels and aluminum shorting ring cap Rear gap-venting Top-Plate Cooling Channels The U Series woofer from Sundown is incredibly versatile, thriving in both competition setups and your daily driver. It features a double-stacked 9” wide ferrite magnet system and a robust top plate. It also incorporates shorting rings within the magnets and pole cap to enhance frequency response, act as a heat sink, and guide airflow. The U Series is equipped with a significantly thicker custom aluminum frame that boasts heat-dissipation ribs. The v.2 motor also includes an extended pole piece to ensure the coil remains controlled even under high stress!

2000 Watts RMS / 4000 Watts Peak Dual 2 or 4 ohm voice coils Optimized for small ported enclosures Aluminum 3” voice coil former for superior heat dissipation High-temperature copper voice coil Double stitched surround Heavy-duty cast basket Spring-loaded terminals accept up to 8-gauge wire Stitched-on heavy-duty tinsel leads Solid pole with vent channels and aluminum shorting ring cap Rear gap-venting Top-Plate Cooling Channels Designed to be at home in the competition lanes or playing your favorite music, the U Series is the premier “standard suspension” woofer in the Sundown lineup. A double-stacked 9.4-inch wide ferrite magnet system is coupled to a thick top plate. A thick set of shorting rings are used inside the magnets and on the pole cap, smoothing out frequency response while doubling as a heat sink and airflow guide. A custom, substantially thicker aluminum frame was designed specifically for the U Series, equipped with heat dissipation ribs. The U v.2 motor also features an extended pole piece to keep the coil under perfect control under high stress. The coil temperature is kept in check via a high-velocity solid pole / machined pole channels arrangement and a series of 16 direct air-gap vents in the back plate.

2000 Watts RMS / 4000 Watts Peak Dual 2 or 4 ohm voice coils Optimized for small ported or bandpass enclosures Aluminum 3” voice coil former for superior heat dissipation High-temperature copper voice coil Double stitched surround Heavy-duty cast basket Spring-loaded terminals accept up to 8-gauge wire Stitched-on heavy-duty tinsel leads Solid pole with vent channels and aluminum shorting ring cap Rear gap-venting Top-Plate Cooling Channels Designed to be at home in the competition lanes or playing your favorite music, the U Series is the premier “standard suspension” woofer in the Sundown lineup. A double-stacked 9.4-inch wide ferrite magnet system is coupled to a thick top plate. A thick set of shorting rings are used inside the magnets and on the pole cap, smoothing out frequency response while doubling as a heat sink and airflow guide. A custom, substantially thicker aluminum frame was designed specifically for the U Series, equipped with heat dissipation ribs. The U v.2 motor also features an extended pole piece to keep the coil under perfect control under high stress. The coil temperature is kept in check via a high-velocity solid pole / machined pole channels arrangement and a series of 16 direct air-gap vents in the back plate.

2000 Watts RMS / 4000 Watts Peak Dual 2 or 4 ohm voice coils Optimized for small ported or bandpass enclosures Aluminum 3” voice coil former for superior heat dissipation High-temperature copper voice coil Double stitched surround Heavy-duty cast basket Spring-loaded terminals accept up to 8-gauge wire Stitched-on heavy-duty tinsel leads Solid pole with vent channels and aluminum shorting ring cap Rear gap-venting Top-Plate Cooling Channels Designed to be at home in the competition lanes or playing your favorite music, the U Series is the premier “standard suspension” woofer in the Sundown lineup. A double-stacked 9.4-inch wide ferrite magnet system is coupled to a thick top plate. A thick set of shorting rings are used inside the magnets and on the pole cap, smoothing out frequency response while doubling as a heat sink and airflow guide. A custom aluminum frame was designed specifically for the U Series. It’s substantially thicker and equipped with heat dissipation ribs at the bottom of the frame. The U v.2 motor also features an extended pole piece to keep the coil under perfect control under high stress. The coil temperature is controlled with machined, high-velocity pole channels and a series of 16 direct air-gap vents in the back plate. Specifications T/S SPECS UV.2 15" D2 UV.2 15" D4 RE (Ohms) 3.8279 6.0586 FS (Hz) 37.1918 36.4015 VAS (L) 43.5048 46.1027 Qes 0.5463 0.6170 Qms 5.4082 5.5975 Qts 0.4962 0.5557 Le (mH) 3.4147 4.6596 BL (NA) 26.7943 31.1468 Mms (Grams) 438.4924 431.9457 Cms (uM/N) 41.7623 44.2561 Sens (dB @ 1w/1m) 87.8716 87.3156 Xmax 30mm 30mm Enclosure Specifications Sealed Enclosure 2.0 cu ft Ported Enclosure 3.0 cu ft Recommended Tuning 35Hz Recommended Port Area 48 sq in Displacement 0.24 cu ft Depth 9.0″ Outside Diameter 15.6″ Cut-Out 14.1″ Physical Dimensions Download Dimensions

2000 Watts RMS / 4000 Watts Peak Dual 2 or 4 ohm voice coils Optimized for small ported or bandpass enclosures Aluminum 3” voice coil former for superior heat dissipation High-temperature copper voice coil Double stitched surround Heavy-duty cast basket Spring-loaded terminals accept up to 8-gauge wire Stitched-on heavy-duty tinsel leads Solid pole with vent channels and aluminum shorting ring cap Rear gap-venting Top-Plate Cooling Channels Designed to be at home in the competition lanes or playing your favorite music, the U Series is the premier “standard suspension” woofer in the Sundown lineup. A double-stacked 9.4-inch wide ferrite magnet system is coupled to a thick top plate. A thick set of shorting rings are used inside the magnets and on the pole cap, smoothing out frequency response while doubling as a heat sink and airflow guide. A custom aluminum frame was designed specifically for the U Series. It’s substantially thicker and equipped with heat dissipation ribs at the bottom of the frame. The U v.2 motor also features an extended pole piece to keep the coil under perfect control under high stress. The coil temperature is controlled with machined, high-velocity pole channels and a series of 16 direct air-gap vents in the back plate. Specifications RE (Ohms) 3.8710 6.0767 FS (Hz) 30.9541 30.9212 VAS (L) 111.7625 114.6901 Qes 0.5669 0.6572 Qms 5.6396 5.5116 Qts 0.5151 0.5872 Le (mH) 3.3981 4.7475 BL (NA) 27.4023 31.4938 Mms (Grams) 565.4130 552.1551 Cms (uM/N) 46.7560 47.9807 Sens (dB @ 1w/1m) 89.4169 88.8733 Xmax 30mm 30mm T/S SPECS UV.2 18" D2 UV.2 18" D4 Enclosure Specifications Sealed Enclosure 3.0 cu ft Ported Enclosure 4.0 cu ft Recommended Tuning 35Hz Recommended Port Area 64 sq in Displacement 0.26 cu ft Depth 10″ Outside Diameter 18.63″ Cut-Out 16.9″ Physical Dimensions Download Dimensions

RMS 400 watts 4 ohm voice coil Made for extremely deep bass Triple-stacked magnet 2.25” voice coil Hyper-extended pole Vented top plate Built to order Designed with an extended pole piece and an incredible four inches of peak-to-peak excursion, the X v.2 is engineered for ultra-deep bass and high power handling. Engineered to set a new standard in the low-frequency/small-ported-box subwoofer category, the X Series can also work in up to a 50% larger enclosure if you desire even more low-end extension. The X v.2 series differentiates itself with its incredibly linear suspension, ensuring the lowest level of bass extension in a small enclosure while maintaining extremely low levels of distortion. Notably, the v.2 series features a much larger motor structure (220mm vs. 190mm on the V.1 series), improved motor ventilation, and an all-new Mega-Roll v.2 surround, providing a more linear and rugged update to the world-famous Mega-Roll v.1 surround design.

1250 Watts RMS / 2500 Watts Peak Dual 2 or 4 ohm voice coil Triple-stacked magnet 2.5” voice coil Hyper-extended pole The X-8 v.4 is THE KING of standard cut-out size 8" subwoofers and it sets the standard for others to follow. It builds on the legacy of the v1, v2, and v3 models but definitively out-performs all previous generations. The secret sauce is largely in the painstakingly FEA optimized spider and surround. It's hard to overstate the impact of proper suspension design on a subwoofer but anyone who has used the X-8 v.4 can attest that we've nailed it here. Beyond the suspension - the X-8 v.4 is built on a newly revised version of our classic custom-tooled 8" frame. It represents the absolute maximum performance possible on this frame platform. The motor and coil are capable of ~20mm of linear x-max one-way and around 2.4" p-p before the coil leaves the gap (with a little beyond that before any physical bottom is reached). As with most of our subs it also features an aluminum magnet ID shorting ring for reduced inductive distortion as well as a few other secret Sundown tricks for distortion reduction!"

The Sundown Audio 10" 3000W XV4 Subwoofer is engineered for true bass lovers who demand precision and power. Designed with advanced X v.4 coil technology, this subwoofer pushes boundaries with exceptional low-frequency performance and high durability. Whether you’re upgrading your car audio system or building a competition setup, the XV4 delivers massive power handling up to 6000W peak  while maintaining clarity and control. It's 30mm Xmax ensures deep, punchy bass notes without distortion, even at high output levels. Built with a strong motor and optimized cone structure, the XV4 offers superior thermal management and consistent performance under pressure. Its 10-inch design fits perfectly into ported enclosures, providing the ideal balance between output and sound quality. Upgrade your ride with the Sundown XV4 — where craftsmanship meets unmatched sound performance. Key Features: Powerful 3000W RMS / 6000W Peak output Advanced X v.4 coil design for improved efficiency 10" subwoofer with deep, accurate bass response Optimized for ported enclosures (1.5 cu ft / 32Hz tuning) 30mm Xmax for maximum excursion and clean bass Heavy-duty motor with 9.25" diameter Durable build for competition-level use Dual 1-Ohm and Dual 2-Ohm impedance options Technical Specifications (for Metafields): Specification Xv4 10D1 Xv4 10D2 RMS Power 3000W 3000W Peak Power 6000W 6000W Displacement 0.22 cu. ft. 0.22 cu. ft. Depth 11" 11" Outside Diameter 11.81" 11.81" Cutout Diameter 10.01" 10.01" Motor Diameter 9.25" 9.25" Sealed Enclosure Not Recommended Not Recommended Ported Enclosure 1.5 cu. ft. 1.5 cu. ft. Recommended Port Tuning 32Hz 32Hz Recommended Port Area 24 sq in 24 sq in 4th Order Sealed Side 0.75 cu ft 0.75 cu ft 4th Order Ported Side 2.25 cu ft 2.25 cu ft 4th Order Port Area 45 sq in 45 sq in 4th Order Port Length 8" 8" Xmax 30mm 30mm Sd (Cone Area) 35.63 35.63 Re (Ohms) 3.2 3.74 Fs (Hz) 41.37 37.04 Vas (L) 8.24 8.

The Sundown Audio Xv4 12" Subwoofer is built for those who demand real power and precision in their sound system. Designed with premium Xv4 coils, this subwoofer delivers a massive 3000 W RMS and 6000 W peak power while maintaining outstanding clarity and control. With a durable, heavy-duty motor and optimized cooling system, the Xv4 ensures consistent performance even during extended play. Whether you’re upgrading your car audio or building a competition-level system, this subwoofer delivers thunderous low frequencies that stay tight and accurate. The precision-engineered cone and suspension system provide minimal distortion and maximum output. Pair it with a well-tuned ported enclosure for deep, room-shaking bass that brings your music to life. Built to handle extreme sound pressure, the Xv4 series continues Sundown Audio’s legacy of reliability, innovation, and unmatched performance. Key Features 12-inch subwoofer with Xv4 voice coils RMS Power: 300 0W , Peak Power: 60 00W Available in Dual 1Ω and Dual 2Ω versions High-efficiency motor structure with strong BL factor Optimized for ported enclosures (2.5 cu. ft @ 32Hz) Xmax: 30mm for deep excursion and accurate bass Reinforced cone for durability under extreme pressure Designed for audiophiles and SPL enthusiasts Technical Specifications (for metafields) Specification XV4 12D1 XV4 12D2 RMS Power 3000W 3000W Peak Power 6000W 6000W Displacement 0.23 cu.ft 0.23 cu.ft Mounting Depth 11.75" 11.75" Outside Diameter 12.81" 12.81" Cutout Diameter 11.09" 11.09" Motor Diameter 9.25" 9.25" Sealed Enclosure Not Recommended Not Recommended Ported Enclosure 2.5 cu.ft @ 32Hz 2.5 cu.ft @ 32Hz Recommended Port Area 40 sq in 40 sq in 4th Order Sealed Side 1.0 cu.ft 1.0 cu.ft 4th Order Ported Side 3.0 cu.ft 3.0 cu.ft 4th Order Port Area 60 sq in 60 sq in 4th Order Port Length 8" 8" Xmax 30mm 30mm Sd (Cone Area) 44.11 44.11 Re (Ω) 2.05 3.25 Fs (Hz) 39.39 36.06 Vas (L) 14.13 15.75 Qes 0.58 0.54 Qms 4.95 4.82 Qts 0.50 0.49 Le (mH) 1.33 2.6 BL (NA) 24.4 22.25 Mms (g) 343.14 367.13 Cms 47.56 53.04 Sensitivity (dB) 83.47 83.06

  The Sundown Audio XV4 15″ Subwoofer delivers the ultimate low-frequency experience for serious bass lovers. Built with the advanced X v.4 coil design, this subwoofer offers extreme power handling and consistent performance under heavy loads. With up to 3000W RMS and 6000W peak power, it ensures clean, distortion-free sound even at the highest volumes. The durable motor structure and optimized cone area (72.58 in²) provide deeper lows and better air displacement for maximum sound pressure. Engineered for flexibility, the XV4 15″ works best in ported enclosures (4.25 cu ft, tuned to 32 Hz) but can also be customized for complex box designs like 4th order setups. Every element — from the high-grade magnet to the precision voice coil — is crafted to deliver unmatched performance and reliability. Perfect for audiophiles and competitors seeking solid bass impact, this subwoofer combines engineering excellence and raw power in one package. Key Features 15″ high-performance subwoofer with X v.4 coils 3000W RMS / 6000W peak power handling 30mm Xmax for strong linear excursion Optimized motor design (9.25″ diameter) Recommended ported box: 4.25 cu ft @ 32 Hz Robust cone design for high SPL output Ideal for competitive and high-end car audio systems Technical Specifications (Metafields Format) Parameter XV4 15D1 XV4 15D2 RMS Power 3000W 3000W Peak Power 6000W 6000W Displacement 0.26 cu.ft. 0.26 cu.ft. Mounting Depth 12.95″ 12.95″ Outside Diameter 15.51″ 15.51″ Cutout Diameter 13.93″ 13.93″ Motor Diameter 9.25″ 9.25″ Sealed Enclosure Not Recommended Not Recommended Ported Enclosure 4.25 cu ft 4.25 cu ft Recommended Port Tuning 32 Hz 32 Hz Recommended Port Area 68 sq in 68 sq in 4th Order Sealed Side 2.0 cu ft 2.0 cu ft 4th Order Ported Side 6.0 cu ft 6.0 cu ft 4th Order Port Area 120 sq in 120 sq in 4th Order Port Length 8″ 8″ Xmax 30mm 30mm SD (Cone Area) 72.58 in² 72.58 in² RE (Ohms) 3.2 3.74 FS (Hz) 29.91 29.51

The Sundown Xv4 18″ Subwoofer delivers unmatched power and control for serious bass enthusiasts. Built with high-grade X v.4 coils, this subwoofer is designed to handle up to 3000W RMS and 6000W peak power, ensuring maximum output without distortion. Its optimized design enhances air movement and cooling, providing long-lasting performance even under heavy use. The advanced motor structure and large cone area (SD 113.41) create powerful low-frequency response and clean sound reproduction. Perfect for sealed or ported enclosures, the Xv4 18″ gives you flexibility in setup and tuning — whether for SPL competition or everyday high-quality listening. Durable, reliable, and beautifully crafted, this subwoofer is the next-level upgrade your sound system deserves. Key Features 18″ Xv4 Series Subwoofer 3000W RMS / 6000W Peak Power Dual 1-Ohm or Dual 2-Ohm Voice Coil Options Precision-engineered X v.4 Coils for stability Heavy-duty motor with 9.25″ diameter Deep bass response with 30 mm Xmax Sealed or ported enclosure compatibility Recommended Port Tuning: 32 Hz Built for extreme durability and clean sound Technical Specifications Specification Value RMS Power 3000 W Peak Power 6000 W Displacement 0.28 cu ft Mounting Depth 15″ Outside Diameter 18.42″ Cutout Diameter 16.69″ Motor Diameter 9.25″ Sealed Enclosure Not Recommended Ported Enclosure 7.00 cu ft Recommended Port Tuning 32 Hz Recommended Port Area 112 sq in 4th Order Sealed Side 3.0 cu ft 4th Order Ported Side 9.0 cu ft 4th Order Port Area 180 sq in 4th Order Port Length 8″ Xmax 30 mm SD (Cone Area) 113.41 RE (Ohms) 2.05 / 3.74 FS (Hz) 25.87 / 25.58 VAS (L) 93.67 Qes 0.63 / 0.55 Qms 4.13 / 4.03 Qts 0.54 / 0.84 BL (NA) 19.74 / 26.8 Mms 737.81 / 656.74 Sensitivity 86 / 87 dB  

Small Size. Serious Power. Unmatched Engineering. Don’t let the size fool you — the Z8 Series 8” subwoofer is built to perform well beyond expectations. With an incredible 2000 watts RMS and 4000 watts peak power handling, this compact beast is ready to drop low, hit hard, and take a beating — all while maintaining control and clarity. Designed for high-output systems with limited space, the Z8 offers the same elite-level engineering found in our larger Z Series drivers, packed into an 8-inch frame. This sub is built around a black aluminum 2.75" 4-layer round-winding voice coil with a massive 30mm Xmax, giving it incredible excursion and power handling for its size. Every component is engineered for airflow and cooling: from the optimized high-velocity pole vent to the cast-aluminum vented frame spacer ring and heavily vented magnetic gap. Add in stitched XL tinsel leads, a Mega-Roll v.2 surround, custom spider packs, and a large aluminum Faraday ring, and you’ve got a sub that’s made for real-world abuse and long-term performance. Designed specifically for ported enclosures (sealed not recommended), the Z8 thrives in a 1.0 cu. ft. net enclosure tuned to 32Hz. Whether you’re building a powerhouse daily driver or squeezing competition-level performance into a tight space, the Z8 delivers big bass in a small footprint — no compromises. Features Power Handling:2000 Watts RMS / 4000 Watts Peak Xmax = 30mm Heavily vented magnetic gap Spring Loaded Terminals Optimized high-velocity pole vent Innovative high-velocity cast-aluminum vented frame spacer ring Black aluminum 2.75 inch 4-layer round-winding voice coil sing our proprietary ultra-thick winding method Mega-Roll v.2 surround Custom tooled basket Large aluminum Faraday (shorting) Ring Stitched-On XL Tinsel Leads to prevent fatigue and failure Custom-tooled ultra-linear spider packs

The Z v.6 is the second step up in Sundown's "ultra-high excursion" subwoofer lineup after the X v.3 series and replaces the world-famous Z v.5 series. All models (10,12,15,18) feature our custom tooled and patented frames (US Patent Numbers D691596, D691597, D691598, and D741841). Sundown mates these new platform frames to a quad stacked 240mm (9.45”) diameter motor structure with a total magnet stack height of 100mm (3.94”) featuring a hyper-extended pole and extreme clearances (allowing over 4" p-p travel before mechanical bottom effectively making it bottomless). Compared to the X v.3 motor both the top & back plates are thicker allowing for even more magnetic strength and excursion potential. For the Z v.6 the top plate is another 5mm thicker than even the outgoing Z v.5 series! This motor drives a 3" diameter 8-Layer Flat Wire Aluminum Voice Coil wound on a thick aluminum former to incredible levels of excursion. The Z v.6 now uses the same voice coil as the NS v.5 series. The Z v.5 utilized a 4-layer voice coil – the change to an 8-layer was to answer our customers desire for higher motor force (more output) and it does just that! Based on Sundown's years of experience with the Z v.4 and Z v.5 series we've also improved the voice coil ventilation to be even more effective. The Z v.6 features a high-velocity pole vent, a heavily vented magnetic gap, and (all new for the v.6) machined channels in four places around the pole piece itself. The Z v.6 series was designed from the ground-up to become the new standard in the low-frequency / small ported box subwoofer category in this price range. They will work in the same small enclosures that are commonly used for for Sundown Audio's subwoofers, although, they can be used with enclosures up to about 50% larger than those if you desire even more low-end extension. The Z v.6 series is really a different kind of woofer due to its incredibly linear suspension. They are designed for the LOWEST level of bass extensi

The Z v.6 is the second step up in Sundown's "ultra-high excursion" subwoofer lineup after the X v.3 series and replaces the world-famous Z v.5 series. All models (10,12,15,18) feature our custom tooled and patented frames (US Patent Numbers D691596, D691597, D691598, and D741841). Sundown mates these new platform frames to a quad stacked 240mm (9.45”) diameter motor structure with a total magnet stack height of 100mm (3.94”) featuring a hyper-extended pole and extreme clearances (allowing over 4" p-p travel before mechanical bottom effectively making it bottomless). Compared to the X v.3 motor both the top & back plates are thicker allowing for even more magnetic strength and excursion potential. For the Z v.6 the top plate is another 5mm thicker than even the outgoing Z v.5 series! This motor drives a 3" diameter 8-Layer Flat Wire Aluminum Voice Coil wound on a thick aluminum former to incredible levels of excursion. The Z v.6 now uses the same voice coil as the NS v.5 series. The Z v.5 utilized a 4-layer voice coil – the change to an 8-layer was to answer our customers desire for higher motor force (more output) and it does just that! Based on Sundown's years of experience with the Z v.4 and Z v.5 series we've also improved the voice coil ventilation to be even more effective. The Z v.6 features a high-velocity pole vent, a heavily vented magnetic gap, and (all new for the v.6) machined channels in four places around the pole piece itself. The Z v.6 series was designed from the ground-up to become the new standard in the low-frequency / small ported box subwoofer category in this price range. They will work in the same small enclosures that are commonly used for for Sundown Audio's subwoofers, although, they can be used with enclosures up to about 50% larger than those if you desire even more low-end extension. The Z v.6 series is really a different kind of woofer due to its incredibly linear suspension. They are designed for the LOWEST level of bass extension possible in a small enclosure while maintaining extremely low levels of distortion. Features Power Handling:3250 Watts RMS / 6500 Watts Peak Xmax = 35mm one-way by 70% BL Heavily vented magnetic gap Spring Loaded Terminals Optimized high-velocity pole vent Innovative high-velocity cast-aluminum vented frame spacer ring Black aluminum 3 inch 8-layer voice coil Mega-Roll v.2 surround Custom tooled basket Large aluminum Faraday (shorting) Ring Stitched-On XL Tinsel Leads to prevent fatigue and failure Custom-tooled ultra-linear spider packs

The Z v.7 is the third step up in Sundown's 2025 "ultra-high excursion" sub-woofer lineup after the M and X v.4 series. All models (12,15,18) feature our custom tooled and patented frames (US Patent Numbers D691597, D691598, and D741841) – the Sundown “mega-platform.” Please note – the Z v.7 is not available, aside from special orders, in 10s due to the motor size. We mate these new platform frames to a quad stacked 265mm (10.43”) diameter motor structure with a total magnet stack height of 100mm (3.94”) featuring a hyper-extended pole and extreme clearances (allowing over 4" p-p travel before mechanical bottom effectively making it bottomless). This is, by far, the largest motor we have ever produced on a Z series sub-woofer. The motor force factor (BL^2/RE) is ~50% higher than the previous generation Z v.6 series. This motor drives a 3.3" diameter 4-Layer Round Wire Aluminum Voice Coil wound on a thick aluminum former. These new round wire coils use a special Sundown designed “fat wire” winding method to handle significant amounts of power and abuse. Based on Sundown's years of experience with the Z v.4, 5, and 6 series we've also improved the voice coil ventilation yet again. The Z v.7 features an entirely new and patent-pending airflow directing pole cap, six pole OD channels, SIXTEEN gap vents, and a cross-drilled / slotted top plate to keep the voice coil running cool under extreme conditions. The Z v.7 motor also features a 9mm thick magnet ID Faraday ring which is locked into both the top and back plates. This ring combined with an all-new pole-extension inductance sleeve gives the Z v.7 the most linear inductive performance of any mega-platform sub-woofer to date. As if all of this were not enough to cement the Z v.7as a legend... we were also able to achieve 42mm of one-way linear excursion by 70% BL with an extremely uniform curve via our extensively FEA optimized motor and 95mm long voice-coil winding length. The Z v.7 series was designed from the ground-up to become the new standard in the low-frequency / small, ported box sub-woofer category in this price range. They will work in the same enclosures that are commonly used for Sundown Audio's mega-platform sub-woofers. The Z v.7 series, like its other mega-platform brethren, is really a different kind of woofer due to its incredibly linear suspension. They are designed for the LOWEST level of bass extension possible in a small enclosure while maintaining extremely low levels of distortion.

The Z v.7 is the third step up in Sundown's 2025 "ultra-high excursion" sub-woofer lineup after the M and X v.4 series. All models (12,15,18) feature our custom tooled and patented frames (US Patent Numbers D691597, D691598, and D741841) – the Sundown “mega-platform.” Please note – the Z v.7 is not available, aside from special orders, in 10s due to the motor size. We mate these new platform frames to a quad stacked 265mm (10.43”) diameter motor structure with a total magnet stack height of 100mm (3.94”) featuring a hyper-extended pole and extreme clearances (allowing over 4" p-p travel before mechanical bottom effectively making it bottomless). This is, by far, the largest motor we have ever produced on a Z series sub-woofer. The motor force factor (BL^2/RE) is ~50% higher than the previous generation Z v.6 series. This motor drives a 3.3" diameter 4-Layer Round Wire Aluminum Voice Coil wound on a thick aluminum former. These new round wire coils use a special Sundown designed “fat wire” winding method to handle significant amounts of power and abuse. Based on Sundown's years of experience with the Z v.4, 5, and 6 series we've also improved the voice coil ventilation yet again. The Z v.7 features an entirely new and patent-pending airflow directing pole cap, six pole OD channels, SIXTEEN gap vents, and a cross-drilled / slotted top plate to keep the voice coil running cool under extreme conditions. The Z v.7 motor also features a 9mm thick magnet ID Faraday ring which is locked into both the top and back plates. This ring combined with an all-new pole-extension inductance sleeve gives the Z v.7 the most linear inductive performance of any mega-platform sub-woofer to date. As if all of this were not enough to cement the Z v.7as a legend... we were also able to achieve 42mm of one-way linear excursion by 70% BL with an extremely uniform curve via our extensively FEA optimized motor and 95mm long voice-coil winding length. The Z v.7 series was designed from the ground-up to become the new standard in the low-frequency / small, ported box sub-woofer category in this price range. They will work in the same enclosures that are commonly used for Sundown Audio's mega-platform sub-woofers. The Z v.7 series, like its other mega-platform brethren, is really a different kind of woofer due to its incredibly linear suspension. They are designed for the LOWEST level of bass extension possible in a small enclosure while maintaining extremely low levels of distortion.

The Z v.7 is the third step up in Sundown's 2025 "ultra-high excursion" sub-woofer lineup after the M and X v.4 series. All models (12,15,18) feature our custom tooled and patented frames (US Patent Numbers D691597, D691598, and D741841) – the Sundown “mega-platform.” Please note – the Z v.7 is not available, aside from special orders, in 10s due to the motor size. We mate these new platform frames to a quad stacked 265mm (10.43”) diameter motor structure with a total magnet stack height of 100mm (3.94”) featuring a hyper-extended pole and extreme clearances (allowing over 4" p-p travel before mechanical bottom effectively making it bottomless). This is, by far, the largest motor we have ever produced on a Z series sub-woofer. The motor force factor (BL^2/RE) is ~50% higher than the previous generation Z v.6 series. This motor drives a 3.3" diameter 4-Layer Round Wire Aluminum Voice Coil wound on a thick aluminum former. These new round wire coils use a special Sundown designed “fat wire” winding method to handle significant amounts of power and abuse. Based on Sundown's years of experience with the Z v.4, 5, and 6 series we've also improved the voice coil ventilation yet again. The Z v.7 features an entirely new and patent-pending airflow directing pole cap, six pole OD channels, SIXTEEN gap vents, and a cross-drilled / slotted top plate to keep the voice coil running cool under extreme conditions. The Z v.7 motor also features a 9mm thick magnet ID Faraday ring which is locked into both the top and back plates. This ring combined with an all-new pole-extension inductance sleeve gives the Z v.7 the most linear inductive performance of any mega-platform sub-woofer to date. As if all of this were not enough to cement the Z v.7as a legend... we were also able to achieve 42mm of one-way linear excursion by 70% BL with an extremely uniform curve via our extensively FEA optimized motor and 95mm long voice-coil winding length. The Z v.7 series was designed from the ground-up to become the new standard in the low-frequency / small, ported box sub-woofer category in this price range. They will work in the same enclosures that are commonly used for Sundown Audio's mega-platform sub-woofers. The Z v.7 series, like its other mega-platform brethren, is really a different kind of woofer due to its incredibly linear suspension. They are designed for the LOWEST level of bass extension possible in a small enclosure while maintaining extremely low levels of distortion.

PSE-6.5 Freq. range 20hz-150hz FS 52hz Xmax 12mm D4 250W RMS Mounting Depth 4.5” Cut out 6”

COMBO DEAL INCLUDES: 4 x BPS-8 8" Pro Sound Co-Axial Speakers 1 x SAM-100.4 400w 4 Channel Micro Amplifier ----------------------- BPS-8 8" Pro Sound Co-Axial Speaker Information: Frequency Range 100hz - 18khz 4 Ohm 150w RMS 94dB Sensitivity [1W/1M] Cutout Diameter: 7.32" Mounting Depth: 4.25" SAM-100.4 400w 4 Channel Micro Amplifier Information: Our SAMv.2 amplifiers are ideal for all your powersports needs. It is a micro amplifier to fit in tight spaces but don’t let its size fool you, they pack some big power. It is rated IP67 waterproof to withstand full submersion when getting wild off-road or when its time to clean up when the fun is done. The multi-channel amps have built in Bluetooth so a source unit is not needed just sync to your phone and enjoy. When your ready to get serious and add subwoofers the mono-block amplifiers link right to your multi-channel RCA for an easy install.

1250 Watts RMS / 2500 Watts Peak Dual 2 or 4 ohm voice coils Vented magnetic gap & pole piece Aluminum 2.75” voice coil former for superior heat dissipation Innovative high velocity, cast aluminum vented frame spacer ring Magnet ID faraday ring for smooth acoustic response High-temperature copper voice coil wire Spring-loaded terminals Stitched-on double “XL” tinsel leads This SA-10/12/15 v.2 series is a top-down upgrade from the original SA series. The 2.75” coil punches way above its weight, outperforming many 3” coils without the adding weight & with the added advantage of a wider spider. We are able to perfectly balance the mass, motor force, and suspension stiffness for the intended power level. The motor also features a large magnet shorting ring (faraday ring) to reduce distortion and deliver smoother response across the entire acoustic spectrum. The motor & coil setup is mated to an extremely robust multi-layer spider with fully tied-on & doubled-up “XL” tinsel leads. A competition-grade paper cone, strong foam surround, and cast aluminum frame are used to complete this masterpiece. On top of the ~19mm of one-way linear excursion we have an x-mech limit of 37mm one-way before coil bottom making it nearly "bottomless." The 18" model features a larger diameter motor to drive the higher mass.

The NS v.5 is the absolute top-tier driver in Sundown's "ultra-high excursion" sub-woofer lineup with a 3” coil. All models (10,12,15,18) feature our custom tooled and patented frames (US Patent Numbers D691596, D691597, D691598, and D741841). Our proprietary frames allow 4” or more of peak-to-peak mechanical excursion. From here the NS (Nightshade) line diverges dramatically from our other lines. The motor is based on our patented S.A.I.N.T. (Sundown Audio Intelligent Neodymium Technology) Design (US Patent Numbers US10382874B2 and USD791740S1). As of the release of the NS v.4/v.5 series these are the only products in our line to utilize this all new and proprietary design. The Nightshade v.5 features an enormous 45mm (1.77”) magnetic gap to ensure the coil is always under control. This motor drives a 3" diameter 8-Layer Flat Wire Aluminum Coil with an extremely long winding (3.15” long) wound on a thick aluminum former to incredible levels of excursion. With the introduction of the new light-weight motors we also incorporated several new cooling / thermal management features to push the power handling up to an enormous 3000-watts RMS: The motor utilizes N52H Neo (heat treated). The entire motor would need to be nearly 250 degrees F before the magnet is affected in any way. This is nearly 40 degrees more than is required to boil water! There are many myths surrounding Neo motors – and none of these apply to the Nightshade. The Neo magnets are sandwiched between two aluminum plates which meet the air gap along their inner edge. These plates help carry the heat away from the gap and thus the magnets and voice coil. The bottom aluminum plate is cooled by the air going in and out of the holes around the motor. The top aluminum plate is cooled by the air-flow from the spider going in and out of vented spacer ring. These plates also serve as very effective shorting rings. Furthermore, the Neo magnets themselves do not directly come into contact with the “air gap” of th

The NS v.5 is the absolute top-tier driver in Sundown's "ultra-high excursion" sub-woofer lineup with a 3” coil. All models (10,12,15,18) feature our custom tooled and patented frames (US Patent Numbers D691596, D691597, D691598, and D741841). Our proprietary frames allow 4” or more of peak-to-peak mechanical excursion. From here the NS (Nightshade) line diverges dramatically from our other lines. The motor is based on our patented S.A.I.N.T. (Sundown Audio Intelligent Neodymium Technology) Design (US Patent Numbers US10382874B2 and USD791740S1). As of the release of the NS v.4/v.5 series these are the only products in our line to utilize this all new and proprietary design. The Nightshade v.5 features an enormous 45mm (1.77”) magnetic gap to ensure the coil is always under control. This motor drives a 3" diameter 8-Layer Flat Wire Aluminum Coil with an extremely long winding (3.15” long) wound on a thick aluminum former to incredible levels of excursion. With the introduction of the new light-weight motors we also incorporated several new cooling / thermal management features to push the power handling up to an enormous 3000-watts RMS: The motor utilizes N52H Neo (heat treated). The entire motor would need to be nearly 250 degrees F before the magnet is affected in any way. This is nearly 40 degrees more than is required to boil water! There are many myths surrounding Neo motors – and none of these apply to the Nightshade. The Neo magnets are sandwiched between two aluminum plates which meet the air gap along their inner edge. These plates help carry the heat away from the gap and thus the magnets and voice coil. The bottom aluminum plate is cooled by the air going in and out of the holes around the motor. The top aluminum plate is cooled by the air-flow from the spider going in and out of vented spacer ring. These plates also serve as very effective shorting rings. Furthermore, the Neo magnets themselves do not directly come into contact with the “air gap” of th

The NS v.5 is the absolute top-tier driver in Sundown's "ultra-high excursion" sub-woofer lineup with a 3” coil. All models (10,12,15,18) feature our custom tooled and patented frames (US Patent Numbers D691596, D691597, D691598, and D741841). Our proprietary frames allow 4” or more of peak-to-peak mechanical excursion. From here the NS (Nightshade) line diverges dramatically from our other lines. The motor is based on our patented S.A.I.N.T. (Sundown Audio Intelligent Neodymium Technology) Design (US Patent Numbers US10382874B2 and USD791740S1). As of the release of the NS v.4/v.5 series these are the only products in our line to utilize this all new and proprietary design. The Nightshade v.5 features an enormous 45mm (1.77”) magnetic gap to ensure the coil is always under control. This motor drives a 3" diameter 8-Layer Flat Wire Aluminum Coil with an extremely long winding (3.15” long) wound on a thick aluminum former to incredible levels of excursion. With the introduction of the new light-weight motors we also incorporated several new cooling / thermal management features to push the power handling up to an enormous 3000-watts RMS: The motor utilizes N52H Neo (heat treated). The entire motor would need to be nearly 250 degrees F before the magnet is affected in any way. This is nearly 40 degrees more than is required to boil water! There are many myths surrounding Neo motors – and none of these apply to the Nightshade. The Neo magnets are sandwiched between two aluminum plates which meet the air gap along their inner edge. These plates help carry the heat away from the gap and thus the magnets and voice coil. The bottom aluminum plate is cooled by the air going in and out of the holes around the motor. The top aluminum plate is cooled by the air-flow from the spider going in and out of vented spacer ring. These plates also serve as very effective shorting rings. Furthermore, the Neo magnets themselves do not directly come into contact with the “air gap” of th

The NS v.5 is the absolute top-tier driver in Sundown's "ultra-high excursion" sub-woofer lineup with a 3” coil. All models (10,12,15,18) feature our custom tooled and patented frames (US Patent Numbers D691596, D691597, D691598, and D741841). Our proprietary frames allow 4” or more of peak-to-peak mechanical excursion. From here the NS (Nightshade) line diverges dramatically from our other lines. The motor is based on our patented S.A.I.N.T. (Sundown Audio Intelligent Neodymium Technology) Design (US Patent Numbers US10382874B2 and USD791740S1). As of the release of the NS v.4/v.5 series these are the only products in our line to utilize this all new and proprietary design. The Nightshade v.5 features an enormous 45mm (1.77”) magnetic gap to ensure the coil is always under control. This motor drives a 3" diameter 8-Layer Flat Wire Aluminum Coil with an extremely long winding (3.15” long) wound on a thick aluminum former to incredible levels of excursion. With the introduction of the new light-weight motors we also incorporated several new cooling / thermal management features to push the power handling up to an enormous 3000-watts RMS: The motor utilizes N52H Neo (heat treated). The entire motor would need to be nearly 250 degrees F before the magnet is affected in any way. This is nearly 40 degrees more than is required to boil water! There are many myths surrounding Neo motors – and none of these apply to the Nightshade. The Neo magnets are sandwiched between two aluminum plates which meet the air gap along their inner edge. These plates help carry the heat away from the gap and thus the magnets and voice coil. The bottom aluminum plate is cooled by the air going in and out of the holes around the motor. The top aluminum plate is cooled by the air-flow from the spider going in and out of vented spacer ring. These plates also serve as very effective shorting rings. Furthermore, the Neo magnets themselves do not directly come into contact with the “air gap” of t

IN STOCK! SUB DEPTH 11.5" SUB MOTOR WIDTH 6 1/2" It has some great new features to increase power handling and to keep heat away from the Neo magnets: ** Side-Vented Motor (more efficient than gap venting)** Newly Tooled Cast Aluminum Venting Ring (transfers heat from the motor into the basket)** Aluminum "top-plate" to transfer heat into the vent ring more effectively** Additional aluminum heat-sink below the Neo Magnets (this is internal and cannot be seen from the outside)** Solid pole-piece for high velocity air movement across the coil former Features & Highlights: 2500-watts RMS80mm long 3" Diameter Flat Wound USA Made Voice Coil Standard** Optional 8-layer for SPL applications (These are ~70mm long)23% More Motor Force than NS v.3 with stock coilLower inductance than NS v.3Only ~50 pounds

SUB DEPTH 15 1/4" SUB MOTOR WIDTH 6 1/2" It has some great new features to increase power handling and to keep heat away from the Neo magnets: ** Side-Vented Motor (more efficient than gap venting)** Newly Tooled Cast Aluminum Venting Ring (transfers heat from the motor into the basket)** Aluminum "top-plate" to transfer heat into the vent ring more effectively** Additional aluminum heat-sink below the Neo Magnets (this is internal and cannot be seen from the outside)** Solid pole-piece for high velocity air movement across the coil former Features & Highlights: 3000-watts RMS80mm long 3" Diameter Flat Wound USA Made Voice Coil Standard** Optional 8-layer for SPL applications (These are ~70mm long)23% More Motor Force than NS v.3 with stock coilLower inductance than NS v.3Only ~50 pounds

The Z v.6 is the second step up in Sundown's "ultra-high excursion" subwoofer lineup after the X v.3 series and replaces the world-famous Z v.5 series. All models (10,12,15,18) feature our custom tooled and patented frames (US Patent Numbers D691596, D691597, D691598, and D741841). Sundown mates these new platform frames to a quad stacked 240mm (9.45”) diameter motor structure with a total magnet stack height of 100mm (3.94”) featuring a hyper-extended pole and extreme clearances (allowing over 4" p-p travel before mechanical bottom effectively making it bottomless). Compared to the X v.3 motor both the top & back plates are thicker allowing for even more magnetic strength and excursion potential. For the Z v.6 the top plate is another 5mm thicker than even the outgoing Z v.5 series! This motor drives a 3" diameter 8-Layer Flat Wire Aluminum Voice Coil wound on a thick aluminum former to incredible levels of excursion. The Z v.6 now uses the same voice coil as the NS v.5 series. The Z v.5 utilized a 4-layer voice coil – the change to an 8-layer was to answer our customers desire for higher motor force (more output) and it does just that! Based on Sundown's years of experience with the Z v.4 and Z v.5 series we've also improved the voice coil ventilation to be even more effective. The Z v.6 features a high-velocity pole vent, a heavily vented magnetic gap, and (all new for the v.6) machined channels in four places around the pole piece itself. The Z v.6 series was designed from the ground-up to become the new standard in the low-frequency / small ported box subwoofer category in this price range. They will work in the same small enclosures that are commonly used for for Sundown Audio's subwoofers, although, they can be used with enclosures up to about 50% larger than those if you desire even more low-end extension. The Z v.6 series is really a different kind of woofer due to its incredibly linear suspension. They are designed for the LOWEST level of bass extensi

The Z v.6 is the second step up in Sundown's "ultra-high excursion" subwoofer lineup after the X v.3 series and replaces the world-famous Z v.5 series. All models (10,12,15,18) feature our custom tooled and patented frames (US Patent Numbers D691596, D691597, D691598, and D741841). Sundown mates these new platform frames to a quad stacked 240mm (9.45”) diameter motor structure with a total magnet stack height of 100mm (3.94”) featuring a hyper-extended pole and extreme clearances (allowing over 4" p-p travel before mechanical bottom effectively making it bottomless). Compared to the X v.3 motor both the top & back plates are thicker allowing for even more magnetic strength and excursion potential. For the Z v.6 the top plate is another 5mm thicker than even the outgoing Z v.5 series! This motor drives a 3" diameter 8-Layer Flat Wire Aluminum Voice Coil wound on a thick aluminum former to incredible levels of excursion. The Z v.6 now uses the same voice coil as the NS v.5 series. The Z v.5 utilized a 4-layer voice coil – the change to an 8-layer was to answer our customers desire for higher motor force (more output) and it does just that! Based on Sundown's years of experience with the Z v.4 and Z v.5 series we've also improved the voice coil ventilation to be even more effective. The Z v.6 features a high-velocity pole vent, a heavily vented magnetic gap, and (all new for the v.6) machined channels in four places around the pole piece itself. The Z v.6 series was designed from the ground-up to become the new standard in the low-frequency / small ported box subwoofer category in this price range. They will work in the same small enclosures that are commonly used for for Sundown Audio's subwoofers, although, they can be used with enclosures up to about 50% larger than those if you desire even more low-end extension. The Z v.6 series is really a different kind of woofer due to its incredibly linear suspension. They are designed for the LOWEST level of bass extensi

The Sundown U Series is our premier “standard suspension” woofer series. It is the most direct replacement for the world famous Z v.3 woofer line which we produced from 2011 to 2016 before launching the “new platform” Z v.4 series. Due to numerous advancements in our design process the U Series is able to deliver performance on-par with the Z v.3 series but at a much lower cost. We start with a double-stacked / 8.66” wide Y35 grade ferrite magnet system coupled to a one-piece, bumped T-Yoke and a 0.6” thick top-plate. Just as with the Z v.3 before it and our other high-end subwoofers we also add a very thick (5mm thickness) aluminum shorting ring inside the magnets to reduce static inductance and level out inductance over stroke. The U series motor also features a 0.6” long pole-extension to keep the coil under control at high levels of excursion. The voice coil is a 2.36” long / 3” diameter 4-layer aluminum winding / aluminum former unit – which is the same coil we use in our X v.2 series and, thus, the U series has the same 1500-watt RMS ratings. The coil temperature is kept in check by a heavily smoothed / high-velocity pole-vent and a series of ten direct air-gap vents in the back plate. The U series also features newly tooled cast aluminum vent rings in between the frame and top plate to effectively exchange air at a high velocity over the voice coil beneath the spider landing. The U series features an all-new cast aluminum frame series to the Sundown line which allows for taller cones than the older frames used on the Z v.3 series. The taller cones provide enhanced coil stability and increased mechanical excursion capability. We also tooled matching cast-aluminum surround clamps for the U series to ensure durability in the most demanding situations. The surrounds and cone bodies have been fully custom tooled especially for the U series and are stronger / support more excursion than the Z v.3 series cones and surrounds. The new cone bodies also feature an indentation for the same wide-flange, ultra-strong dust caps as our new platform subwoofers. If you are looking for a woofer that sounds similar to the SA series but handles significantly more power… the U series is exactly what you need. It has been designed to live up to the reputation earned by our Z v.3 series both in terms of every-day music enjoyment and SPL competition. Specifications Black Aluminum 3” voice coil former for superior heat dissipation High Temperature Round-Wire CCAW voice coil with high-temp black adhesive Double stitched surround Heavy duty cast basket Spring loaded terminals accept up to 8 gauge Stitched-on double-XL tinsel leads Rear vented pole piece Rear drilled gap-venting Innovative high-velocity cast aluminum vented frame spacer ring Magnet ID shorting ring Top-Plate Cooling Channels Cast Aluminum surround bolt-on rings Optimized for small ported or bandpass enclosures

The Sundown U Series is our premier “standard suspension” woofer series. It is the most direct replacement for the world famous Z v.3 woofer line which we produced from 2011 to 2016 before launching the “new platform” Z v.4 series. Due to numerous advancements in our design process the U Series is able to deliver performance on-par with the Z v.3 series but at a much lower cost. We start with a double-stacked / 8.66” wide Y35 grade ferrite magnet system coupled to a one-piece, bumped T-Yoke and a 0.6” thick top-plate. Just as with the Z v.3 before it and our other high-end subwoofers we also add a very thick (5mm thickness) aluminum shorting ring inside the magnets to reduce static inductance and level out inductance over stroke. The U series motor also features a 0.6” long pole-extension to keep the coil under control at high levels of excursion. The voice coil is a 2.36” long / 3” diameter 4-layer aluminum winding / aluminum former unit – which is the same coil we use in our X v.2 series and, thus, the U series has the same 1500-watt RMS ratings. The coil temperature is kept in check by a heavily smoothed / high-velocity pole-vent and a series of ten direct air-gap vents in the back plate. The U series also features newly tooled cast aluminum vent rings in between the frame and top plate to effectively exchange air at a high velocity over the voice coil beneath the spider landing. The U series features an all-new cast aluminum frame series to the Sundown line which allows for taller cones than the older frames used on the Z v.3 series. The taller cones provide enhanced coil stability and increased mechanical excursion capability. We also tooled matching cast-aluminum surround clamps for the U series to ensure durability in the most demanding situations. The surrounds and cone bodies have been fully custom tooled especially for the U series and are stronger / support more excursion than the Z v.3 series cones and surrounds. The new cone bodies also feature an indentation for the same wide-flange, ultra-strong dust caps as our new platform subwoofers. If you are looking for a woofer that sounds similar to the SA series but handles significantly more power… the U series is exactly what you need. It has been designed to live up to the reputation earned by our Z v.3 series both in terms of every-day music enjoyment and SPL competition. Specifications Black Aluminum 3” voice coil former for superior heat dissipation High Temperature Round-Wire CCAW voice coil with high-temp black adhesive Double stitched surround Heavy duty cast basket Spring loaded terminals accept up to 8 gauge Stitched-on double-XL tinsel leads Rear vented pole piece Rear drilled gap-venting Innovative high-velocity cast aluminum vented frame spacer ring Magnet ID shorting ring Top-Plate Cooling Channels Cast Aluminum surround bolt-on rings Optimized for small ported or bandpass enclosures

2500 Watts RMS / 5000 Watts Peak Dual 1 or 2 ohm voice coil Made for extremely deep bass Triple-stacked magnet 3” voice coil Hyper-extended pole Built to order Designed with an extended pole piece and an incredible four inches of peak-to-peak excursion, the X v.3 is engineered for ultra-deep bass and high power handling. Engineered to set a new standard in the low-frequency/small-ported-box subwoofer category, the X Series can also work in up to a 50% larger enclosure if you desire even more low-end extension. The X v.3 series differentiates itself with its incredibly linear suspension, ensuring the lowest level of bass extension in a small enclosure while maintaining extremely low levels of distortion. Notably, the v.3 series features a much larger motor structure (220mm vs. 190mm on the v.1 series), improved motor ventilation, and an all-new Mega-Roll v.2 surround, providing a more linear and rugged update to the world-famous Mega-Roll v.1 surround design. Specifications RE (Ohms) 1.4 3.2 FS (Hz) 39.104 40.208 VAS (L) 11.623 9.352 Qes 0.441 0.528 Qms 2.567 2.842 Qts 0.376 0.445 Le (mH)     BL (NA) 14.155 21.509 Mms (Grams) 256.970 302.089 Cms (uM/N) 64.465 51.867 Sens (dB @ 1w/1m) 83.8dB 82.5dB Xmax 30mm 30mm T/S SPECS X V.3 10″ D1 X V.3 10″ D2 Enclosure Specifications X v.3 8 X v.3 10 X v.3 12 X v.3 15 X v.3 18 Sealed Enclosure 0.3-.04cuft N/A N/A N/A N/A Ported Enclosure 0.75-1.0 cu ft 1.5 cu ft 2.5 cu ft 4.25 cu ft 7.00 cu ft Recommended Tuning 32hz 32hz 32hz 32hz 32hz Recommended Port Area 12-16 sq in 24 sq in 40 sq in 68 sq in 112 sq in Displacement 0.13 cu ft 0.21 cu ft 0.2 cu ft 0.22 cu ft 0.23 cu ft Depth 6.8" 9.4" 10.4" 11.6" 13.6" Outside Diam. 8.70" 11.65" 12.68" 15.51" 18.42" Cutout 7.36" 10.01" 11.09" 13.83" 16.69" Physical Dimensions Download Download Download Download Download

2500 Watts RMS / 5000 Watts Peak Dual 1 or 2 ohm voice coil Made for extremely deep bass Triple-stacked magnet 3” voice coil Hyper-extended pole Built to order Designed with an extended pole piece and an incredible four inches of peak-to-peak excursion, the X v.3 is engineered for ultra-deep bass and high power handling. Engineered to set a new standard in the low-frequency/small-ported-box subwoofer category, the X Series can also work in up to a 50% larger enclosure if you desire even more low-end extension. The X v.3 series differentiates itself with its incredibly linear suspension, ensuring the lowest level of bass extension in a small enclosure while maintaining extremely low levels of distortion. Notably, the v.3 series features a much larger motor structure (220mm vs. 190mm on the v.1 series), improved motor ventilation, and an all-new Mega-Roll v.2 surround, providing a more linear and rugged update to the world-famous Mega-Roll v.1 surround design. Specifications T/S SPECS X V.3 12″ D1 X V.3 12″ D2 RE (Ohms) 1.4 3.2 FS (Hz) 37.098 37.235 VAS (L) 12.986 17.077 Qes 0.486 0.543 Qms 2.597 2.779 Qts 0.409 0.454 Le (mH)     BL (NA) 15.943 19.857 Mms (Grams) 378.626 285.817 Cms (uM/N) 48.611 63.922 Sens (dB @ 1w/1m) 83.2dB 84.0dB Xmax 30mm 30mm Enclosure Specifications   X v.3 12 Sealed Enclosure N/A Ported Enclosure 2.5 cu ft Recommended Tuning 32hz Recommended Port Area 40 sq in Displacement 0.2 cu ft Depth 10.4" Outside Diam. 12.68" Cutout 11.09" Physical Dimensions Download Enclosure Designs .Zip File

2500 Watts RMS / 5000 Watts Peak Dual 1 or 2 ohm voice coil Made for extremely deep bass Triple-stacked magnet 3” voice coil Hyper-extended pole Built to order Designed with an extended pole piece and an incredible four inches of peak-to-peak excursion, the X v.3 is engineered for ultra-deep bass and high power handling. Engineered to set a new standard in the low-frequency/small-ported-box subwoofer category, the X Series can also work in up to a 50% larger enclosure if you desire even more low-end extension.  The X v.3 series differentiates itself with its incredibly linear suspension, ensuring the lowest level of bass extension in a small enclosure while maintaining extremely low levels of distortion. Notably, the v.3 series features a much larger motor structure (220mm vs. 190mm on the V.1 series), improved motor ventilation, and an all-new Mega-Roll v.2 surround, providing a more linear and rugged update to the world-famous Mega-Roll v.1 surround design. Specifications T/S SPECS X V.3 15″ D1 X V.3 15″ D2 RE (Ohms) 1.4 3.2 FS (Hz) 31.418 31.423 VAS (L) 45.907 45.924 Qes 0.486 0.561 Qms 2.562 2.801 Qts 0.409 0.468 Le (mH)     BL (NA) 15.518 21.831 Mms (Grams) 423.721 423.436 Cms (uM/N) 60.563 60.585 Sens (dB @ 1w/1m) 86.5dB 85.9dB Xmax 30mm 30mm Enclosure Specifications X v.3 15 Sealed Enclosure N/A Ported Enclosure 4.25 cu ft Recommended Tuning 32hz Recommended Port Area 68 sq in Displacement 0.22 cu ft Depth 11.6" Outside Diam. 15.51" Cutout 13.83" Physical Dimensions Download Enclosure Designs .Zip File

2500 Watts RMS / 5000 Watts Peak Dual 1 or 2 ohm voice coil Made for extremely deep bass Triple-stacked magnet 3” voice coil Hyper-extended pole Built to order Designed with an extended pole piece and an incredible four inches of peak-to-peak excursion, the X v.3 is engineered for ultra-deep bass and high power handling. Engineered to set a new standard in the low-frequency/small-ported-box subwoofer category, the X Series can also work in up to a 50% larger enclosure if you desire even more low-end extension. The X v.3 series differentiates itself with its incredibly linear suspension, ensuring the lowest level of bass extension in a small enclosure while maintaining extremely low levels of distortion. Notably, the v.3 series features a much larger motor structure (220mm vs. 190mm on the v.1 series), improved motor ventilation, and an all-new Mega-Roll v.2 surround, providing a more linear and rugged update to the world-famous Mega-Roll v.1 surround design. Specifications RE (Ohms) 1.4 3.2 FS (Hz) 26.650 28.207 VAS (L) 130.302 109.935 Qes 0.526 0.657 Qms 2.793 3.091 Qts 0.442 0.542 Le (mH)     BL (NA) 14.543 20.854 Mms (Grams) 474.114 504.115 Cms (uM/N) 75.224 63.154 Sens (dB @ 1w/1m) 88.6dB 87.6dB Xmax 30mm 30mm T/S SPECS X V.3 18″ D1 X V.3 18″ D2 Enclosure Specifications X v.3 18 Sealed Enclosure N/A Ported Enclosure 7.00 cu ft Recommended Tuning 32hz Recommended Port Area 112 sq in Displacement 0.23 cu ft Depth 13.6" Outside Diam. 18.42" Cutout 16.69" Physical Dimensions Download Enclosure Designs .Zip File

The X-8 v.3 is pretty much THE KING of 8" subwoofers and, certainly, is one of the most popular 8s we've ever produced during its 4+ years in continuous production. It builds on the legacy of the v1 and v2 models but definitively trounces both of them in every way. The secret sauce is largely in the painstakingly FEA optimized spider and surround. It's hard to overstate the impact of proper suspension design on a subwoofer but anyone who has used the X-8 v.3 can attest that we've nailed it here. Beyond the suspension - the X-8 v.3 is built on our custom-tooled 8" frame. It represents the absolute maximum performance possible on this frame platform - nearly 10 years after tooling the frame for the SA-8 v2 we have completely maxed it out! The motor and coil are capable of ~20mm of linear x-max one-way and around 2.4" p-p before the coil leaves the gap (with a little beyond that before any physical bottom is reached). As with most of our subs it also features an aluminum magnet ID shorting ring for reduced inductive distortion as well as a few other secret Sundown tricks for distortion reduction! It's safe to say that the 800-watt RMS rating is quite conservative.

The Z v.6 is the second step up in Sundown's "ultra-high excursion" subwoofer lineup after the X v.3 series and replaces the world-famous Z v.5 series. All models (10,12,15,18) feature our custom tooled and patented frames (US Patent Numbers D691596, D691597, D691598, and D741841). Sundown mates these new platform frames to a quad stacked 240mm (9.45”) diameter motor structure with a total magnet stack height of 100mm (3.94”) featuring a hyper-extended pole and extreme clearances (allowing over 4" p-p travel before mechanical bottom effectively making it bottomless). Compared to the X v.3 motor both the top & back plates are thicker allowing for even more magnetic strength and excursion potential. For the Z v.6 the top plate is another 5mm thicker than even the outgoing Z v.5 series! This motor drives a 3" diameter 8-Layer Flat Wire Aluminum Voice Coil wound on a thick aluminum former to incredible levels of excursion. The Z v.6 now uses the same voice coil as the NS v.5 series. The Z v.5 utilized a 4-layer voice coil – the change to an 8-layer was to answer our customers desire for higher motor force (more output) and it does just that! Based on Sundown's years of experience with the Z v.4 and Z v.5 series we've also improved the voice coil ventilation to be even more effective. The Z v.6 features a high-velocity pole vent, a heavily vented magnetic gap, and (all new for the v.6) machined channels in four places around the pole piece itself. The Z v.6 series was designed from the ground-up to become the new standard in the low-frequency / small ported box subwoofer category in this price range. They will work in the same small enclosures that are commonly used for for Sundown Audio's subwoofers, although, they can be used with enclosures up to about 50% larger than those if you desire even more low-end extension. The Z v.6 series is really a different kind of woofer due to its incredibly linear suspension. They are designed for the LOWEST level of bass extension possible in a small enclosure while maintaining extremely low levels of distortion. Features Power Handling:3250 Watts RMS / 6500 Watts Peak Xmax = 35mm one-way by 70% BL Heavily vented magnetic gap Spring Loaded Terminals Optimized high-velocity pole vent Innovative high-velocity cast-aluminum vented frame spacer ring Black aluminum 3 inch 8-layer voice coil Mega-Roll v.2 surround Custom tooled basket Large aluminum Faraday (shorting) Ring Stitched-On XL Tinsel Leads to prevent fatigue and failure Custom-tooled ultra-linear spider packs

The Z v.6 is the second step up in Sundown's "ultra-high excursion" subwoofer lineup after the X v.3 series and replaces the world-famous Z v.5 series. All models (10,12,15,18) feature our custom tooled and patented frames (US Patent Numbers D691596, D691597, D691598, and D741841). Sundown mates these new platform frames to a quad stacked 240mm (9.45”) diameter motor structure with a total magnet stack height of 100mm (3.94”) featuring a hyper-extended pole and extreme clearances (allowing over 4" p-p travel before mechanical bottom effectively making it bottomless). Compared to the X v.3 motor both the top & back plates are thicker allowing for even more magnetic strength and excursion potential. For the Z v.6 the top plate is another 5mm thicker than even the outgoing Z v.5 series! This motor drives a 3" diameter 8-Layer Flat Wire Aluminum Voice Coil wound on a thick aluminum former to incredible levels of excursion. The Z v.6 now uses the same voice coil as the NS v.5 series. The Z v.5 utilized a 4-layer voice coil – the change to an 8-layer was to answer our customers desire for higher motor force (more output) and it does just that! Based on Sundown's years of experience with the Z v.4 and Z v.5 series we've also improved the voice coil ventilation to be even more effective. The Z v.6 features a high-velocity pole vent, a heavily vented magnetic gap, and (all new for the v.6) machined channels in four places around the pole piece itself. The Z v.6 series was designed from the ground-up to become the new standard in the low-frequency / small ported box subwoofer category in this price range. They will work in the same small enclosures that are commonly used for for Sundown Audio's subwoofers, although, they can be used with enclosures up to about 50% larger than those if you desire even more low-end extension. The Z v.6 series is really a different kind of woofer due to its incredibly linear suspension. They are designed for the LOWEST level of bass extension possible in a small enclosure while maintaining extremely low levels of distortion. Features Power Handling:3250 Watts RMS / 6500 Watts Peak Xmax = 35mm one-way by 70% BL Heavily vented magnetic gap Spring Loaded Terminals Optimized high-velocity pole vent Innovative high-velocity cast-aluminum vented frame spacer ring Black aluminum 3 inch 8-layer voice coil Mega-Roll v.2 surround Custom tooled basket Large aluminum Faraday (shorting) Ring Stitched-On XL Tinsel Leads to prevent fatigue and failure Custom-tooled ultra-linear spider packs

The Z v.6 is the second step up in Sundown's "ultra-high excursion" subwoofer lineup after the X v.3 series and replaces the world-famous Z v.5 series. All models (10,12,15,18) feature our custom tooled and patented frames (US Patent Numbers D691596, D691597, D691598, and D741841). Sundown mates these new platform frames to a quad stacked 240mm (9.45”) diameter motor structure with a total magnet stack height of 100mm (3.94”) featuring a hyper-extended pole and extreme clearances (allowing over 4" p-p travel before mechanical bottom effectively making it bottomless). Compared to the X v.3 motor both the top & back plates are thicker allowing for even more magnetic strength and excursion potential. For the Z v.6 the top plate is another 5mm thicker than even the outgoing Z v.5 series! This motor drives a 3" diameter 8-Layer Flat Wire Aluminum Voice Coil wound on a thick aluminum former to incredible levels of excursion. The Z v.6 now uses the same voice coil as the NS v.5 series. The Z v.5 utilized a 4-layer voice coil – the change to an 8-layer was to answer our customers desire for higher motor force (more output) and it does just that! Based on Sundown's years of experience with the Z v.4 and Z v.5 series we've also improved the voice coil ventilation to be even more effective. The Z v.6 features a high-velocity pole vent, a heavily vented magnetic gap, and (all new for the v.6) machined channels in four places around the pole piece itself. The Z v.6 series was designed from the ground-up to become the new standard in the low-frequency / small ported box subwoofer category in this price range. They will work in the same small enclosures that are commonly used for for Sundown Audio's subwoofers, although, they can be used with enclosures up to about 50% larger than those if you desire even more low-end extension. The Z v.6 series is really a different kind of woofer due to its incredibly linear suspension. They are designed for the LOWEST level of bass extension possible in a small enclosure while maintaining extremely low levels of distortion. Features Power Handling:3250 Watts RMS / 6500 Watts Peak Xmax = 35mm one-way by 70% BL Heavily vented magnetic gap Spring Loaded Terminals Optimized high-velocity pole vent Innovative high-velocity cast-aluminum vented frame spacer ring Black aluminum 3 inch 8-layer voice coil Mega-Roll v.2 surround Custom tooled basket Large aluminum Faraday (shorting) Ring Stitched-On XL Tinsel Leads to prevent fatigue and failure Custom-tooled ultra-linear spider packs