
DC Audio is an American manufacturer specializing in high-performance subwoofers and amplifiers for SPL competition and serious bass enthusiasts. Founded by William "Rusty" Flowers and based in Sparks, Nevada, DC Audio hand-assembles competition-grade products with over 20 years of expertise in the competition lanes. Their Level series (Levels 1-6) features progressive power handling up to 4500W RMS, heavy-duty construction with FEA-optimized motors, advanced cooling, and massive excursion. DC Audio is a prominent sponsor of major SPL competitions and their products are the choice of car audio competitors worldwide chasing record-breaking SPL scores.

The DC Audio 15M3D2 is a high-performance subwoofer featuring a 4-inch cone with dual 2 voice coil configuration. Rated at 2000W RMS. Designed for deep bass reproduction and high SPL output.

[ D2 Version ] The m4 8 is an 8" long X-Max subwoofer. We have been asked for an 8 that smashes the lows and takes power. This is an 8 that will give those that asked exactly what they are looking for. A tall roll stitched surround, oversized spiders, and a taller cast frame than the m3. These newly designed parts allow for lower frequency reproduction and higher power handling. The bolted-down spaced spider design keeps it all linear. The m4 8 uses a gap-cooled design to allow the 2.5" voice coil to thermally take more power than the m3. Key Features:Extremely rigid non-pressed paper cone assembly High Roll Stitched Multilayered reinforced polymer foam surround. Rigid propylene dust cover with White DC logo Bolted down & spaced Linear roll spiders. Sewn flat heavy-duty tinsel lead wire. Custom Cast black aluminum frame FEA analyzed and optimized motor assembly – Fully CNC machined. Rubber mounting gasket and custom tooled motor boot. DVC 2.5” Copper voice coil.

Subwoofer Description The PS3 sub is the result of countless hours of R&D. We built, and rebuilt over and over to bring you a subwoofer that is designed to be in a sealed or ported box BUT work in a open air environment . These guys are at home pounding out the bass on a Bagger Motorcycles , Slingshots or Side by Sides. The PS3 sub has a 2.5mm aluminum shorting ring to help reduce inductance as well as a very specific set of soft parts that makes this driver come to life in open air. It has rear gap venting, a pole vent, triple stacked FEA optimized motor with a custom tooled magnet boot. 1250 watts RMS 2500 watts Peak PowerKey Features Extremely rigid non-pressed paper cone assembly Multilayered polymer foam surround Polypropylene dust cover with DC logo Triple 8” OD semi cup progressive roll spider Extra heavy duty interweaved tinsel lead wire sewn to spider Cast aluminum black frame / no invert mount FEA analyzed and optimized motor assembly – Fully CNC machined Rubber mounting gasket Chrome spring loaded push terminals 3” Hi-temp custom voice coil wound on black anodized voice coil former Rubber magnet cover 2.5mm Aluminum shorting ringT/S Parameters PS3 Subwoofer10"12"Mounting Depth6.125"6.56"Mounting Hole Diameter9.35"11"Outside Driver Diameter11"12.5"VC Diameter3.0"3.0"Displacement.15 ft³.16 ft³Power Handling rms/peak1250/25001250/2500Ohm Optionsd1/d2d1/d2Sd303 cm²457 cm²Vas6.02 L12.64 LCms45.71 uM/n42.56 uM/nMms352.94 g453.67 gFs39.60 Hz36.21 HzBl21.77 N/A21.65 N/ARe4.11 Ohm4.18 OhmLe2.81 mH2.98 mHQms9.1111.21Qes0.760.92Qts0.7030.851Xmax23mm23mmRef SPL @1 watt78.65 db79.89 dbSuggest Sealed Box.65 ft³1.0 ft³Suggested Ported Box1.0 ft³1.25 ft³PS3 Subwoofer15"18"Mounting Depth8.0"9.5"Mounting Hole Diameter14.0"16.75"Outside Driver Diameter15.7"18.5"VC Diameter3.0"3.0"Displacement.18 ft³.22 ft³Power Handling rms/peak1250/25001250/2500Ohm Optionsd1/d2d1/d2Sd823 cm²1217 cm²Vas00.0 L000.0 LCms0.00 Mm/n0.00 Mm/nMms000 g000 gFs00.0 Hz00.0 HzBl00.0 N/A00.0 N/ARe0.0 Ohm0.0 OhmLe0.0 mH0.0 mHQms0.000.00Qes0.0000.000Qts0.000.000Xmax23mm23mmRef SPL @1 watt00.0 db00.0 dbSuggest Sealed Box2.0 ft³3.5 ft³Suggested Ported Box3.0 ft³5.5 ft³

DC Audio Shortie Subwoofers Sizes Available: 10/12 Inch Model Ohms Available: D2 & D4 Models Power Handling: 500 Watts RMS 1000 Watts PeakDC Audio Shortie Got limited Mounting Depth?? DC has a answer It starts out with a single slug FEA optimized motor. A chrome top plate and T yoke. 2.5" voice coil, Glossy Black stamped Steel Frame, Side Motor Venting, push terminals and a rating suggestion of 500w RMS/1000w peak power handling. This sub works great in sealed or ported enclosures.Key Features • Stitched surround and paper cone assembly • Rubber Motor boot with DC Logo • Polypropylene dust cover with DC logo • Heavy duty interweaved tinsel lead wire sewn to the spider • Cast Aluminum black frame • FEA analyzed and optimized motor assembly - Fully CNC machined with Machined side venting • Rubber mounting gasket • Chrome spring loaded push terminals • 2.5” voice coil T/S Parameters 10"12"Mounting Depth5"5.48"Mounting Hole Diameter9.3"11.0"Outside Driver Diameter11"12.5"VC Diameter2.5"2.5"Displacement.11 ft.14Power Handling rms/peak500/1000500/1000Ohm Optionsd2/d4d2/d4Sd346cm552cmVas 7.17L18.47LCms121.53um/n47.065u M?NMms218g301.6gFs45.5Hz41.9HzBl15.67N/A19.067N/ARe7 Ohm4 OhmLemHmHQms4.382

The DC Audio DC-M4 is a high-performance subwoofer featuring a 4-inch cone with dual 2 voice coil configuration. Rated at 600W RMS. Designed for deep bass reproduction and high SPL output.

The Neo Elite is DC Audio’s 4” Coil Neo powered subwoofer. Why, Because people asked for it and we thought it would be a fun project, thats exactly what it turned out to be. The Neo Elite is a subwoofer thats happy doing SPL but is even more suited for high power ground pounder applications. If your in the market for a subwoofer that can take alot of power get loud and crush lows then this could be the one for you. The Neo Elite comes with a Large flat wound 4” Coil, 10” Spaced Spiders, The DC Frame, 6 colums of NEO, multi tensil leads sewn to the top spider and a High Performance cone and surround.Sub Size15"18"Mounting Depth12.00"13.00"Mounting Hole Diameter14.25"16.90"Outside Driver Diameter15.70"18.50"Motor Width10.0"10.0"Weight65lbs69lbsVC Diameter4"4"Displacement60lbs60lbsMagnet Weight.22³ ft.27³ ftPower Handling RMS/Peak4500 / 90004500 / 9000Impedance (Ohm)D.7 / D1 / D1.4 /D2D.7 / D1 / D1.4 /D2Sd815cm²1217cm²VasComing SoonComing SoonCmsComing SoonComing SoonMmsComing SoonComing SoonFsComing SoonComing SoonBLComing SoonComing SoonReComing SoonComing SoonLeComing SoonComing SoonQmsComing SoonComing SoonQesComing SoonComing SoonQtsComing SoonComing SoonXmaxComing SoonComing SoonRef SPL @ 1 wattComing SoonComing SoonSuggested Sealedn/an/aSuggested Ported3.0³ ft5.5³ ft

Subwoofer Description The Level 4 m4 is a step forward in SQ and heat dissapation vs the last genaration model (m3). It now comes with a 2.5mm Aluminum Shorting ring (demodulation ring) to help reduce inductance in the motor. This can help with power compression. It also acts as a internal heatsink by pulling heat from the windings into the aluminum ring and the direct to coil venting cycles air across the coil wingings and aluminum shorting ring at the same time cooling them simultaneously. Newly tooled Motor boots withthe DC Logo and LV4 logo embossed on them With fantastic power handling and smashing lows its hard to beat. The Level 4 sub is a large triple stacked motor with a chrome top plate and T yoke yielding 23.5mm of X-Max. Furthermore, you get the upgraded triple progressive spiders, cone, surround, 3" coil, cast basket, push terminals and upgraded lead wire sewn to the spider. This sub is rated at 1500w RMS and 3000w peak.Key Features • Extremely rigid non-pressed paper cone assembly • Multilayered polymer foam stitched surround • Polypropylene dust cover with DC logo • Triple 8” OD semi cup progressive roll spider • Extra heavy duty interweaved tinsel lead wire sewn to spider • Cast aluminum black frame / no invert mount • FEA analyzed and optimized motor assembly – Fully CNC machined • Rubber mounting gasket • Chrome spring loaded push terminals • 3” Hi-temp Aluminum voice coil wound on black anodized voice coil former 8 Layer Flat Wound • Rubber magnet cover with DC and Lv4 Logos 5mm Aluminum Shorting ringM4 Level 4 Subwoofer10"12"Mounting Depth6.25"6.75"Mounting Hole Diameter9.35"11"Outside Driver Diameter11"12.5"VC Diameter3.0"3.0"Displacement.16 ft³.18 ft³Power Handling rms/peak1500/30001500/3000Ohm Optionsd1/d2/d4d1/d2/d4Sd324 cm²418 cm²Vas00.00 L17.42 LCms0.000 Mm/n0.058 Mm/nMms000.0 g232.74 gFs00.0 Hz43 HzBl28.49 N/A28.49 N/ARe8.6 Ohm8.6 OhmLe0.00 mH5.62 mHQms0.007.92Qes0.000.66Qts0.0000.615Xmax23.5mm23.5mmRef SPL @1 watt84 db84.94 dbSuggest Sealed Box.75 ft³1.0 ft³Suggested Ported Box1.0 ft³1.5 ft³M4 Level 4 Subwoofer15"18"Mounting Depth8"9.5"Mounting Hole Diameter14.0"16.75"Outside Driver Diameter15.7"18.5"VC Diameter3.0"3.0"Displacement.21 ft³.26 ft³Power Handling rms/peak1500/30001500/3000Ohm Optionsd1/d2/d4d1/d2/d4Sd823 cm²1217 cm²Vas00.00 L000.00 LCms0.000 Mm/n0.000 Mm/nMms000.0 g000.0 gFs00.0 Hz00.0 HzBl00.0 N/A00.0 N/ARe8.6 Ohm8.6 OhmLe0.00 mH0.00 mHQms00.000.0Qes0.0000.000Qts0.000.001Xmax23.5mm23.5mmRef SPL @1 watt00.0 db00.0 dbSuggest Sealed Box2.0 ft³3.5 ft³Suggested Ported Box3.0 ft³5.5 ft³

About the Product Build Time D0.7 Model 7-14 DaysD1.0 Model 7-14 DaysD1.4 Model 7-14 DaysD2.0 Model 7-14 DaysDC Audio Level 6 Elite Subwoofer Model: level 6 M6 New for 2025 Sizes Available: 15 and 18 Inch Models Power Handling: 4500 Watts RMS 9000 Watts Peak The Lv6m6 Elite is DC Audio’s 4” Coil Beast. It has evolved into what most big builds are after, a sub that can take lots of power and Crush Out the Lows!! With a world that has access to amplifiers of today's size we knew we needed a subwoofer that could keep up. A Large flat wound 4” Coil and 10” Spaced Spiders with Plenty of Xmax clearance is what we have to offer in the Level 6!! The new Lv6m6 Elite will find itself at home in the SPL lanes or slappin down your hometowns cruise strip. To really step it up with this driver take a look at the Carbon Fiber cone and dustcap options available for it. New features include a wire cut top plate, Full inner Aluminum sleeve shortning ring, Longer pole and more rearward coil clearance. We have also tooled a new Motor boot with a embossed DC Audio and LV6 Logo on it.Key Features Extremely strong kraft pulp fiber reinforced cone Wide Long Throw foam surround Dome propylene dust cover with White DC logo 10” OD Spaced Spiders Extra heavy duty sewn tinsel lead wire Cast DC Series aluminum black frame / no invert mount FEA analyzed and optimized motor assembly – Fully CNC machined Rubber mounting gasket 8 AWG OFC Direct leads 4.0” 8 Layer Hi-temp Aluminum voice coil wound on a Black Anodized Aluminum former Rubber magnet cover Aluminum shortening ring Extended Pole T/S Parameters 15"18"Mounting Depth12.5"13.5"Mounting Hole Diameter14.25"16.90"Outside Driver Diameter15.7"18.5"VC Diameter4.0"4.0"Displacement.24 ft.27ftPower Handling rms/peak4500/90004500/9000Ohm Optionsd.7/d1/d1.4/d2/d4d.7/d1/d1.4/d2/d4Sd815 cm1159 cmVas46.3L88.75LCms0.057 mm/n00.049 mm/nMms583.6 g748.83 gFs27.59 Hz26.37 HzBl36.41 N/A36.15 N/ARe4.77 Ohm5.39 OhmLe2.02 mH4.64 mHQms5.7266.871Qes0.36430.5119Qts0.34250.4764Xmax32mm32mmRef SPL @1 watt86.16 db86.92 dbSuggest Sealed BoxN/A ftN/A ftSuggested Ported Box3.5 ft6.0 ft

The DC Audio M3-8 8" Subwoofer is a high-performance subwoofer featuring a 3-inch cone with dual 2 voice coil configuration. Thiele-Small parameters: Fs=41.5Hz, Qts=0.799. Maximum linear excursion (Xmax): 22mm. Designed for deep bass reproduction and high SPL output.

The DC Audio M3LV312D2 is a high-performance subwoofer featuring a 3-inch cone with dual 2 voice coil configuration. Designed for deep bass reproduction and high SPL output.

The DC Audio M4-8D4 is a high-performance subwoofer featuring a 4-inch cone with dual 4 voice coil configuration. Rated at 1600W RMS. Designed for deep bass reproduction and high SPL output.

The DC Audio M4XL18D2 is a high-performance subwoofer featuring a 4-inch cone with dual 2 voice coil configuration. Designed for deep bass reproduction and high SPL output.

The DC Audio XL12 is a high-performance subwoofer featuring a 12-inch cone with dual 2 voice coil configuration. Rated at 4400W RMS. Designed for deep bass reproduction and high SPL output.



















