Sundown Audio Speakers

Each Sold Seperately 150 Watts RMS Frequency Range 4khz – 20khz Impedance 4ohms

COMBO DEAL INCLUDES:4 x BPS-6.5 6.5" Pro Sound Co-Axial Speakers1 x SAM-100.4 400w 4 Channel Micro Amplifier----------------------- BPS-6.5 6.5" Pro Sound Co-Axial Speaker Information: Frequency Range 100hz - 18khz 4 Ohm 100w RMS 94dB Sensitivity [1W/1M] Cutout Diameter: 5.82" Mounting Depth: 3.75" SAM-100.4 400w 4 Channel Micro Amplifier Information: Our SAMv.2 amplifiers are ideal for all your powersports needs. It is a micro amplifier to fit in tight spaces but don’t let its size fool you, they pack some big power. It is rated IP67 waterproof to withstand full submersion when getting wild off-road or when its time to clean up when the fun is done. The multi-channel amps have built in Bluetooth so a source unit is not needed just sync to your phone and enjoy. When your ready to get serious and add subwoofers the mono-block amplifiers link right to your multi-channel RCA for an easy install.

COMBO DEAL INCLUDES:4 x BPS-8 8" Pro Sound Co-Axial Speakers1 x SAM-100.4 400w 4 Channel Micro Amplifier----------------------- BPS-8 8" Pro Sound Co-Axial Speaker Information: Frequency Range 100hz - 18khz 4 Ohm 150w RMS 94dB Sensitivity [1W/1M] Cutout Diameter: 7.32" Mounting Depth: 4.25" SAM-100.4 400w 4 Channel Micro Amplifier Information: Our SAMv.2 amplifiers are ideal for all your powersports needs. It is a micro amplifier to fit in tight spaces but don’t let its size fool you, they pack some big power. It is rated IP67 waterproof to withstand full submersion when getting wild off-road or when its time to clean up when the fun is done. The multi-channel amps have built in Bluetooth so a source unit is not needed just sync to your phone and enjoy. When your ready to get serious and add subwoofers the mono-block amplifiers link right to your multi-channel RCA for an easy install.

Frequency Range 100hz - 18khz 4 Ohm 100w RMS 94dB Sensitivity [1W/1M] Cutout Diameter: 5.82" Mounting Depth: 3.75"

Frequency Range 100hz - 18khz 4 Ohm 150w RMS 94dB Sensitivity [1W/1M] Cutout Diameter: 7.32" Mounting Depth: 4.25"

100 Watts RMS Impedance: 4 or 8 Ohms Frequency range: 4kHz - 20kHz Sensitivity 100dB Sold individually Handling 100 watts and only 1.6 inches deep, the BT-R1 is the choice when you want to cut through bass like a hot knife through butter. With an incredible 100dB sensitivity and a wide frequency range, this super tweeter makes the most out of every watt you give it. Enclosure Specifications Download

100 Watts RMS Impedance: 4 or 8 Ohms  Frequency range: 4kHz - 20kHz Sensitivity 100dB Sold individually  Handling 100 watts and only 1.6 inches deep, the BT-R1 is the choice when you want to cut through bass like a hot knife through butter. With an incredible 100dB sensitivity and a wide frequency range, this super tweeter makes the most out of every watt you give it. Enclosure Specifications Download

50W RMS Black polypropylene cone UV-resistant rubber surround High-performance titanium dome tweeter Rubber tweeter stalk ring for weather and dust resistance Black stamped steel basket with perimeter venting Sold as pairs Grilles included 2.5" Mounting depth Sundown’s constant innovation continues in the affordable E-Series coaxial speakers. Designed for audiophiles and enthusiasts alike, these speakers give you crisp highs, rich mids, and deep, impactful bass as only the kings of the SPL lanes can deliver. Using a titanium tweeter and tough polypropylene cone, the E-Series drivers use a damped titanium tweeter for smooth response, without the harshness of most metal drivers. An ultra smooth sounding polypropylene cone is mated to the cone with a rubber surround, helping to provide extremely linear excursion. A rubber sealing ring was added to the tweeter stalk, preventing dust and moisture from interfering with motor movement. The steel frame is custom tooled and vented for outstanding thermal control, so you can play it long and play it loud!

100W RMS Black polypropylene cone UV-resistant rubber surround High-performance titanium dome tweeter Rubber tweeter stalk ring for weather and dust resistance Black stamped steel basket with perimeter venting Sold as pairs Grilles included Sundown continues its tradition of innovation with the affordable E-Series component speakers. Designed for both audiophiles and enthusiasts, these speakers provide crisp highs, rich mids, and deep, impactful bass, delivering the quality expected of SPL champions. The E-Series drivers feature a damped titanium tweeter and a polypropylene cone to ensure smooth response. The speakers also use a rubber surround to provide extremely linear excursion. Additionally, the custom-tooled, vented steel frame ensures outstanding thermal control for extended, high-volume use.

60W RMS Black polypropylene cone UV-resistant rubber surround High-performance titanium dome tweeter Rubber tweeter stalk ring for weather and dust resistance Black stamped steel basket with perimeter venting Sold as pairs Grilles included 2.5" Mounting depth Sundown continues its tradition of innovation with the affordable E-Series coaxial speakers. Designed for both audiophiles and enthusiasts, these speakers provide crisp highs, rich mids, and deep, impactful bass, delivering the quality expected of SPL champions. The E-Series drivers feature a damped titanium tweeter and a polypropylene cone to ensure smooth response. The speakers also use a rubber surround to provide extremely linear excursion for smooth, natural sound. To prevent dust and moisture from affecting motor movement, a rubber sealing ring has been added to the tweeter stalk. Additionally, the custom-tooled, vented steel frame ensures outstanding thermal control, allowing for extended, high-volume use.

90W RMS Black polypropylene cone UV-resistant rubber surround High-performance titanium dome tweeter Rubber tweeter stalk ring for weather and dust resistance Black stamped steel basket with perimeter venting Sold as pairs Grilles included 3" mounting depth Sundown continues its tradition of innovation with the affordable E-Series coaxial speakers. Designed for both audiophiles and enthusiasts, these speakers provide crisp highs, rich mids, and deep, impactful bass, delivering the quality expected of SPL champions. The E-Series drivers feature a damped titanium tweeter and a polypropylene cone to ensure smooth response. The speakers also use a rubber surround to provide extremely linear excursion. To prevent dust and moisture from affecting motor movement, a rubber sealing ring has been added to the tweeter stalk. Additionally, the custom-tooled, vented steel frame ensures outstanding thermal control, so it sounds great and keeps up with your subs all day long!

100W RMS Black polypropylene cone UV-resistant rubber surround High-performance titanium dome tweeter Rubber tweeter stalk ring for weather and dust resistance Black stamped steel basket with perimeter venting Sold as pairs Grilles included 3.5" mounting depth Sundown’s constant innovation continues in the affordable E-Series coaxial speakers. Designed for audiophiles and enthusiasts alike, these speakers give you crisp highs, rich mids, and deep, hard-hitting bass! Using a titanium tweeter and tough polypropylene cone, the E-Series drivers use a damped titanium tweeter for smooth response, without the harshness of most metal drivers. An ultra smooth sounding polypropylene cone is mated to the cone with a rubber surround, helping to provide extremely linear excursion. A rubber sealing ring was added to the tweeter stalk, preventing dust and moisture from interfering with motor movement. The steel frame is custom tooled and vented for outstanding thermal control, so you can play it long and play it loud!

Features Sold Individually Power Handling: 50 Watts RMS Impedance: 4 ohms Frequency Range: 80Hz - 20kHz Sensitivity: 94dB

Features Sold Individually Power Handling: 60 Watts RMS Impedance: 4 ohms Frequency Range: 60Hz - 20kHz Sensitivity: 94dB

The Sundown Audio high-output tweeter line has been designed to offer our customers the option of several of top quality models. The BT, GT, and ET models will all sound fairly similar - the user will simply pick which one fits their install the best whether it be mounting flange requirements or overall size. The BT and GT both feature a 25.4mm diaphragm where the ET models steps up to a 33.5mm diaphragm. Features Sold Individually Power Handling: 100 Watts RMS Impedance: 4 Ohm or 8 ohm Frequency Range: 4kHz - 20kHz Sensitivity 105dB Download

Power handling: 100 Watts RMS Impedance: 4 or 8 ohms Frequency range: 4kHz - 20kHz Sensitivity: 105dB Sold Individually Handling 100 watts and only 1.67 inches deep, the BT-R1 is the choice when you want to cut through bass like a hot knife through butter. We incorporated our highest sensitivity (105dB) and biggest diaphragm (33.5mm) into this super tweeter to make the most out of every watt you give it. Measurements Download

  Power handling: 100 Watts RMS Impedance: 4 or 8 ohms Frequency range: 4kHz - 20kHz Sensitivity: 105dB Sold Individually Handling 100 watts and only 1.67 inches deep, the BT-R1 is the choice when you want to cut through bass like a hot knife through butter. We incorporated our highest sensitivity (105dB) and biggest diaphragm (33.5mm) into this super tweeter to make the most out of every watt you give it. Measurements Download

The Sundown Audio high-output tweeter line has been designed to offer our customers the option of several of top quality models. The BT, GT, and ET models will all sound fairly similar - the user will simply pick which one fits their install the best whether it be mounting flange requirements or overall size. The BT and GT both feature a 25.4mm diaphragm where the ET models steps up to a 33.5mm diaphragm. Features Sold Individually Power Handling: 100 Watts RMS Impedance: 4 Ohm Frequency Range: 4kHz - 20kHz Sensitivity 100dB

Power Handling: 100 Watts RMS Impedance: 4 or 8 Ohms Frequency range: 4kHz - 20kHz Sensitivity 100dB Sold Individually Handling 100 watts and sporting a slender mounting ring, the GT-R1 is the choice when you want the tweeter to take up a smaller footprint on your door, but want to hear those highs no matter how loud the bass is. With an incredible 100dB sensitivity and a wide frequency range, this super tweeter makes the most out of every watt you give it.

  Power Handling: 100 Watts RMS Impedance: 4 or 8 Ohms Frequency range: 4kHz - 20kHz Sensitivity 100dB Sold Individually Handling 100 watts and sporting a slender mounting ring, the GT-R1 is the choice when you want the tweeter to take up a smaller footprint on your door, but want to hear those highs no matter how loud the bass is.  With an incredible 100dB sensitivity and a wide frequency range, this super tweeter makes the most out of every watt you give it.

Each Sold Seperately 150 Watts RMS Frequency Range 4khz – 20khz Impedance 4ohms

Features Sold Individually Power Handling: 120 Watts RMS Impedance: 4/8 Ohm Frequency Range: 20Hz - 10kHz Phase Plug Outside Diameter: 10.23" Cutout Diameter: 9.17" Mounting Depth: 3.25" Resonant Frequency, FS: 69.45Hz D.C.Voice coil resistance, Re: 3.3 Mechanical quality factor, Qms: 13.22 Electrical quality factor, Qes: 0.44 Total quality factor, Qts: 0.42 Equivalent air volume to Cms. Vas: 49.14L Mechanical compliance, Cms: 0.24MM/N BL factor, Bl: 6.3N/A Effective surface area,Sd: 12.469Mm* Sensitivitv(1w/1m): 96.18dB +/- 2dB

Features Sold Individually Power Handling: 100 Watts RMS Impedance: 4/8 Ohm Frequency Range: 120Hz - 6kHz Phase Plug Outer Diameter: 6.51" Cutout Diameter: 5.82" Mounting Depth: 3.50" VC Diamete: 1.51" Magnet Material: Ferrite Resonant Frequency, FS: 83.27Hz D.C.Voice coil resistance, Re: 3.2 Mechanical quality factor, Qms: 4.1 Electrical quality factor, Qes: 0.43 Total quality factor, Qts: 0.409 Equivalent air volume to Cms. Vas: 7.5L Mechanical compliance, Cms: 0.24MM/N BL factor, Bl: 6.3N/A Effective surface area,Sd: 12.469* Sensitivitv(1w/1m): 92dB +/- 2dB

Features Sold Individually Power Handling: 100 Watts RMS Impedance: 4/8 Ohm Frequency Range: 120Hz - 6kHz Phase Plug Outside Diameter: 8.25" Cutout Diameter: 7.125" Mounting Depth: 3.50" Resonant Frequency, FS: 81.18Hz D.C.Voice coil resistance, Re: 3.2 Mechanical quality factor, Qms: 9.46 Electrical quality factor, Qes: 0.55 Total quality factor, Qts: 0.52 Equivalent air volume to Cms. Vas: 7.5L Mechanical compliance, Cms: 0.24MM/N BL factor, Bl: 6.3N/A Effective surface area,Sd: 12.469Mm* Sensitivitv(1w/1m): 94dB +/- 2dB

Power Handling: 150W-340W Watts RMS 4 or 8 Ohms Carbon fiber cone Neodymium motor Spring loaded terminals Sold Individually Neo motors and carbon fiber cones – there’s nothing better! Made specifically for car audio PA systems, we chose a carbon-fiber cone to handle high SPL systems without breakup, then joined it with a vented, high strength neodymium motor to deliver amazing volume and clarity.

Power Handling: 180W-450W Watts RMS 180W RMS at Full Range 450W RMS at 100hz HPF Sensitivity is 99dB 4 or 8 Ohms Carbon fiber cone Neodymium motor Spring loaded terminals Sold Individually Neo motors and carbon fiber cones – there’s nothing better! Made specifically for car audio PA systems, we chose a carbon-fiber cone to handle high SPL systems without breakup, then joined it with a vented, high strength neodymium motor to deliver amazing volume and clarity.

NEOPRO V.3 6.5" The NeoPro V3 line is Sundown Audio's solution to the weak mid-bass produced by "Pro Sound" style speakers in a car door. Most Pro style speakers are designed for ported boxes as they are re-purposed "club" or "DJ" style speakers. The NeoPro line was specifically engineered for car audio usage! The NeoPro speakers are well known for their smooth sound as much as for their incredible levels of output.. The v.3 version utilized a carbon fiber cone to increase durability in high SPL setups. Features Power Handling: 180 Watts RMS Sold Individually

Power Handling: 125W-300W Watts RMS 4 or 8 Ohms Carbon fiber cone Neodymium motor Spring loaded terminals Sold Individually Neo motors and carbon fiber cones – there’s nothing better! Made specifically for car audio PA systems, we chose a carbon-fiber cone to handle high SPL systems without breakup, then joined it with a vented, high strength neodymium motor to deliver amazing volume and clarity.

NEOPRO V.3 8" The NeoPro V3 line is Sundown Audio's solution to the weak mid-bass produced by "Pro Sound" style speakers in a car door. Most Pro style speakers are designed for ported boxes as they are re-purposed "club" or "DJ" style speakers. The NeoPro line was specifically engineered for car audio usage! The NeoPro speakers are well known for their smooth sound as much as for their incredible levels of output.. The v.3 version utilized a carbon fiber cone to increase durability in high SPL setups. Features Power Handling: 200 Watts RMS Sold Individually

Power Handling: 130W-320W Watts RMS 4 or 8 Ohms Carbon fiber cone Neodymium motor Spring loaded terminals Sold Individually Neo motors and carbon fiber cones – there’s nothing better! Made specifically for car audio PA systems, we chose a carbon-fiber cone to handle high SPL systems without breakup, then joined it with a vented, high strength neodymium motor to deliver amazing volume and clarity.

The Down4Sound NMR65 Neo Mid Range Speaker - 6.5 Inch, 110W RMS is a premium car audio speaker featuring a 4-inch driver. Power handling: 110W RMS. Engineered for clear, detailed sound reproduction.

The Down4Sound NMR654 Neo Mid Range Speaker - 6.5 Inch, 110W RMS is a premium car audio speaker featuring a 4-inch driver. Power handling: 110W RMS. Engineered for clear, detailed sound reproduction.

8 Speaker 300 watt Amplified Bluetooth Powersports Soundbar IPX67 Rated 6 x 3” Full Range Marine Grade Poly Cone Speakers 2 x 1.25” SD Mylar Tweeters Heavy Duty Extruded Aluminum Water Tight Housing LED backlit Control Panel LED Visual Notifications Audible Power On/Off Notifications Built In DSP Processor w/Distortion Limiter Bluetooth input. AUX input (3.5mm) AUX output (3.5mm) USB thumb drive input 3 Volt Line Output Waterproof Wire Loom Connectors Universal L-Bracket Mounting System Included Universal Top or Bottom Mount Clamp Style Brackets

Integrated 300-watt amplifier 6 x 3” full range marine-grade poly cone speakers 2 x 1.25” SD mylar tweeters IPX67 rated (Submersible) Heavy duty extruded aluminum watertight housing LED-backlit control panel Visual notifications Audible power on/off notifications Built in dsp processor w/distortion limiter Bluetooth input Aux input & output (3.5mm) USB thumb drive input Waterproof wire loom connectors Universal l-bracket mounting system included Universal top or bottom mount clamp style brackets The 300-watt Sundown Audio PSSB-8000 soundbar blasts your music through six powerful marine-grade speakers and two crisp mylar tweeters. The rugged, IPX67-rated waterproof design and heavy-duty aluminum housing ensures it can withstand the toughest conditions. Mud, sand or water won’t stop the music! Stay connected and in control with the LED-backlit control panel, Bluetooth input, and multiple connectivity options, including 3.5mm AUX and USB inputs. Whether you're hitting the dunes, navigating rough trails, or cruising the waterways, the PSSB lets you focus on the thrill of the ride. It’s more than a soundbar; it’s your ticket to a lot more fun!

The all-new 2025 Sundown SA speaker series has been designed to make a statement. What statement, you may ask? That Sundown Audio can be just as serious about SQ as we are about SPL. Many people already know this but our subwoofers – even the ones used for crushing demos – have some of the lowest distortion on the market. We are now bringing our unique approach to the more dedicated Sound Quality market.Starting at the upper end of the frequency spectrum we have the SA-1T Tweeter. The SA-1T features a 25.5mm silk dome (total 38mm including surround) driven by a powerful neodymium motor structure. The dome features a compact, tuned back chamber which helps it to achieve its extremely low FS around 700hz. This gives you an enormous amount of flexibility in choosing the crossover. The tweeter can be used as a 2-way with the 6.5M or the 8M models or as part of a three way with either and the 3M model. In addition to the low FS and smooth response the SA-1T has a very high 92dB sensitivity so it doesn't take much power to get loud enough for just about anyone. The SA-1T is the 4th generation SA tweeter building on the success of the tweeter found in the SA Component sets over three generations.Headed down the spectrum to the midrange we have the SA-3M. This "little" unit is something incredibly special and is a favorite project of lead product designer / founder Jacob Fuller. We really went all-out on this unit to address the "big 3" drivers of distortion. The SA-3M features 4.5mm of one-way linear excursion by 70% BL (with 8mm x-mech thanks to the custom tooled frame – so no bottoming out even on powerful dynamics) and over 6mm by CMS and LE definitions on Klippel. There is essentially NO risk of the driver reaching linearity limits in most applications. The beefy motor structure is a combination of ferrite and a neodymium pole cap magnet to help us reach 84.5dB sensitivity at 1-watt. There is a double LE treatment internal to the motor via both a copper pole sleeve an

The all-new 2025 Sundown SA speaker series has been designed to make a statement. What statement, you may ask? That Sundown Audio can be just as serious about SQ as we are about SPL. Many people already know this but our subwoofers – even the ones used for crushing demos – have some of the lowest distortion on the market. We are now bringing our unique approach to the more dedicated Sound Quality market. Starting at the upper end of the frequency spectrum we have the SA-1T Tweeter. The SA-1T features a 25.5mm silk dome (total 38mm including surround) driven by a powerful neodymium motor structure. The dome features a compact, tuned back chamber which helps it to achieve its extremely low FS around 700hz. This gives you an enormous amount of flexibility in choosing the crossover. The tweeter can be used as a 2-way with the 6.5M or the 8M models or as part of a three way with either and the 3M model. In addition to the low FS and smooth response the SA-1T has a very high 92dB sensitivity so it doesn't take much power to get loud enough for just about anyone. The SA-1T is the 4th generation SA tweeter building on the success of the tweeter found in the SA Component sets over three generations. Headed down the spectrum to the midrange we have the SA-3M. This "little" unit is something incredibly special and is a favorite project of lead product designer / founder Jacob Fuller. We really went all-out on this unit to address the "big 3" drivers of distortion. The SA-3M features 4.5mm of one-way linear excursion by 70% BL (with 8mm x-mech thanks to the custom tooled frame – so no bottoming out even on powerful dynamics) and over 6mm by CMS and LE definitions on Klippel. There is essentially NO risk of the driver reaching linearity limits in most applications. The beefy motor structure is a combination of ferrite and a neodymium pole cap magnet to help us reach 84.5dB sensitivity at 1-watt. There is a double LE treatment internal to the motor via both a copper pole sleeve and an aluminum magnet ID shorting ring allowing the SA-3M to play full-range to beyond 20khz (although, for several reasons, we do suggest using a tweeter for the top-end). On the bottom end they can be high-pass crossed over at 300hz effortlessly with 150-watts of power handling (thanks to the 28mm diameter, extra-long voice coil) or even lower if needed, with less power, due to the incredibly high linear stroke. The suspension system, surround and spider, of the SA-3M took over a year of FEA simulations and testing to reach perfection and is just as important as the motor to the resulting low distortion. We gave the suspension just as much attention as we would for a full blown high-stroke subwoofer. To finish off this masterpiece we tested several different types of woven carbon fiber cones & dust caps to achieve the best FR possible. To finish off the 2025 SA speaker line we created the SA-6.5M and the SA-8M. Both of which can be used as a mid-bass or mid-range speaker depending on your application. Both drivers feature the same attention to detail as the 3M regarding the carbon cone and dust cap, surround, and spider. All of these parts were fully FEA simulated and Klippel verified. The SA-6.5M features 5.9mm one-way linear excursion by 70% BL, 7mm by CMS, and 6.28mm by LE on Klippel. Thanks to the efficient motor venting and ample voice coil the power handling is rated for 110-watts full range / 200-watts with a 70hz HPF filter with a respectable 89dB sensitivity. As with the SA-1T this is a 4th generation SA speaker due to the SA component set from prior generations. For this iteration we optimized it further and also created a new custom-tooled frame. The revised frame is more aerodynamics and also allows for superior coil ventilation. As with most Sundown products you will find a thick magnet-ID Faraday ring as well. Last, but absolutely not least, we have the SA-8M which takes linear stroke to yet another level. We were able to achieve 9mm one-way linear by 70% BL and nearly 10mm by CMS and LE standards. As with the 3M, the 8M features a pole sleeve and magnet ID faraday ring for LE treatment. This unit is an absolute powerhouse for mid-bass, and we believe it will make big waves in the SQ world. On the output side it has a 91.5dB sensitivity and will handle 130-watts full-range / 250-watts with a 70Hz HPF thanks to the efficient motor venting and huge 2" coil. The SA-8M is all-in on SQ and output potential – the Sundown way! SA Series, Version 4 1" Soft Dome Tweeter Pair Sensitivity – 92dB 50W RMS @ 3000hz 6dB Crossover 50W RMS @ 3000hz 12dB Crossover 65W RMS @ 5000hz 12dB Crossover

OEM replacement for Dodge/Chrysler dashboards. 4mm Linear Excursion (two-way) Inverted Rubber Surround Aluminum Dust Cap Frequency Response: 200 Hz - 20,000 Hz 30 Watts RMS Drop-in upgrade for Dodge/Chrysler Extended frequency response Custom-voiced cone with aluminum dust cap Never settle for stock sound! Upgrade your Dodge or Chrysler dashboard with the SA-2.75 component speaker, designed as the perfect OEM replacement for a seamless factory fit and a massive upgrade in sound quality. With an impressive 4mm linear excursion, inverted rubber surround, and aluminum dust cap, this speaker is built for durability and high performance. With an extended frequency response of 200 Hz all the way to 20kHz ensures that every note is extraordinarily crisp, full sound – with an incredibly simple installation using factory mounting points. Hear the difference quality makes.

When Sundown set out to design the "SA" series component they knew it had to be something special; something to uphold the reputation of the SA series subwoofer line. But at the same time the price had to remain reasonable; something that almost anyone can afford. The SA component set starts out with its custom designed midrange driver. The mid features a high quality cast aluminum basket as its starting point; where many speakers in this category go with cheaper stamped steel frames. The cone is a carefully selected blend of paper and wool fibers designed to damp any unwanted resonances. The dust cap is a soft poly whose size, shape, and material were all chosen to create the least amount of breakup and distortion as possible. The surround is a very compliant rubber that helps to tame any remaining edge resonances within the cone. With any midrange the cone, surround, and dust cap are CRITICAL to the sound. When designing the SA set we had no concern for fancy cosmetics or other "audio jewelry" The motor was FEA optimized in-house to increase linear excursion and features a full 6mm one-way linear excursion thanks to a carefully designed motor and extended pole piece. We also thoroughly considered thermal performance in the design with the SA mid featuring a vented magnetic gap and a vented voice coil collar. The 60-watt per side power rating on the SA mid is derived from a full 8-hour test on pink noise (full bandwidth down to 20 Hz) -- so when crossed over on the bottom-end this figure ends up being VERY conservative. Most customers use 100+ watt RMS amplifiers on the SA sets. The SA series tweeter had to match the smooth sound of the midrange so we went with a silk dome. We tested numerous versions, tweaked the gap, dome material, tested various lenses, various chamber damping materials, so on and so forth until arriving at the final design. As the response graph is proof of the result is an incredibly smooth sounding tweeter. Don't be fooled by the simple housing -- as we are all taught not to judge a book by its cover and you will find this tweeter performs as good or better than many fancier looking counterparts. We stuck with the Sundown mentality of not spending money where it doesn't increase performance. The crossover is also relatively simple looking at first glance but it does the job perfectly. It is a 12 dB network centered at 3800 Hz with high quality air core inductors and Mylar capacitors. It also features the ability to change the LPF on the mid from a 12dB, to 6dB, to a bypassed slope as well as to adjust the tweeter from 0, to -3, to -6 dB levels. We are confident that anyone who is after a smooth sounding set will be incredibly pleased with the SA component line. Reviews have been overwhelmingly positive on them from all over the globe. If you are a metal or hard dome tweeter fan it may not be your set but we will develop a "sharper" sounding set down the line! Features & Specifications 6.5" Component Speakers System 125 Watts / Side Silk Dome Tweeter Machine Aluminum Tweeter Housing Case Aluminum Frame Magnet ID Shorting Ring (Midrange) Carbon Fiber Cone Rubber Surround 24dB/Octave Crossover Adjustable Tweeter Level (-3, 0, +3) Mounting Depth: 2.87" Cutout: 5.63"

120 watts RMS Silk dome tweeter Hybrid fiber cone Adjustable crossover - midrange and tweeter Cast aluminum frame Magnet ID shorting ring (midrange) Machined aluminum tweeter housing High-compliance rubber surround 2.75" DEPTH Sundown’s premiere sound quality separates, the SA-6.5CS is a marvel of design and top-tier components. The midrange features a high-quality cast aluminum basket, housing a cone with a carefully selected blend of paper and wool fibers. This design dampens any unwanted resonances for an incredibly smooth, detailed response. The surround is a high-compliance rubber, engineered to tame edge resonances within the cone. An FEA-optimized motor was designed in-house, and features a full 6mm one-way linear excursion - thanks to a carefully designed motor and extended pole piece. To increase thermal performance, the SA midrange features a vented magnetic gap and vented voice coil collar. The SA series silk dome tweeter matches the smooth sound of the midrange. A result of extensive testing, Sundown optimized the tweeter’s gap, dome material, lens, and chamber damping material. The results speak for themselves. The separates feature a 12 dB network centered at 3800 Hz, with high quality air core inductors and Mylar capacitors. Change the midrange low pass filter to your acoustic tastes from a 12dB, to 6dB, to a bypassed slope. The tweeter's response is also customizable, ranging from 0, to -3, to -6 dB levels. The SA separates were engineered for one, simple goal: to let you completely immerse yourself in the music. At any volume. For as long as you want.

125 W RMS Silk dome tweeter Hybrid fiber cone Integrated crossover Cast aluminum frame Premium spring-loaded speaker terminals SPL: 91 Db Frequency range: 45Hz - 20KHz Sundown’s premiere sound quality separates, the SA-6.5CS is a marvel of design and top-tier components. The midrange features a high-quality cast aluminum basket, housing a cone with a carefully selected blend of paper and wool fibers. This design dampens any unwanted resonances for an incredibly smooth, detailed response. The surround is a high-compliance rubber, engineered to tame edge resonances within the cone. An FEA-optimized motor was designed in-house and features a full 6mm one-way linear excursion - thanks to a carefully designed motor and extended pole piece. To increase thermal performance, the SA midrange features a vented magnetic gap and vented voice coil collar. The SA series silk dome tweeter matches the smooth sound of the midrange. After extensive testing, Sundown optimized the tweeter’s gap, dome material, lens, and chamber damping material. The results speak for themselves. The SA separates were engineered for one, simple goal: to let you completely immerse yourself in the music. At any volume. For as long as you want.

The all-new 2025 Sundown SA speaker series has been designed to make a statement. What statement, you may ask? That Sundown Audio can be just as serious about SQ as we are about SPL. Many people already know this but our subwoofers – even the ones used for crushing demos – have some of the lowest distortion on the market. We are now bringing our unique approach to the more dedicated Sound Quality market. Starting at the upper end of the frequency spectrum we have the SA-1T Tweeter. The SA-1T features a 25.5mm silk dome (total 38mm including surround) driven by a powerful neodymium motor structure. The dome features a compact, tuned back chamber which helps it to achieve its extremely low FS around 700hz. This gives you an enormous amount of flexibility in choosing the crossover. The tweeter can be used as a 2-way with the 6.5M or the 8M models or as part of a three way with either and the 3M model. In addition to the low FS and smooth response the SA-1T has a very high 92dB sensitivity so it doesn't take much power to get loud enough for just about anyone. The SA-1T is the 4th generation SA tweeter building on the success of the tweeter found in the SA Component sets over three generations. Headed down the spectrum to the midrange we have the SA-3M. This "little" unit is something incredibly special and is a favorite project of lead product designer / founder Jacob Fuller. We really went all-out on this unit to address the "big 3" drivers of distortion. The SA-3M features 4.5mm of one-way linear excursion by 70% BL (with 8mm x-mech thanks to the custom tooled frame – so no bottoming out even on powerful dynamics) and over 6mm by CMS and LE definitions on Klippel. There is essentially NO risk of the driver reaching linearity limits in most applications. The beefy motor structure is a combination of ferrite and a neodymium pole cap magnet to help us reach 84.5dB sensitivity at 1-watt. There is a double LE treatment internal to the motor via both a copper pole sleeve and an aluminum magnet ID shorting ring allowing the SA-3M to play full-range to beyond 20khz (although, for several reasons, we do suggest using a tweeter for the top-end). On the bottom end they can be high-pass crossed over at 300hz effortlessly with 150-watts of power handling (thanks to the 28mm diameter, extra-long voice coil) or even lower if needed, with less power, due to the incredibly high linear stroke. The suspension system, surround and spider, of the SA-3M took over a year of FEA simulations and testing to reach perfection and is just as important as the motor to the resulting low distortion. We gave the suspension just as much attention as we would for a full blown high-stroke subwoofer. To finish off this masterpiece we tested several different types of woven carbon fiber cones & dust caps to achieve the best FR possible. To finish off the 2025 SA speaker line we created the SA-6.5M and the SA-8M. Both of which can be used as a mid-bass or mid-range speaker depending on your application. Both drivers feature the same attention to detail as the 3M regarding the carbon cone and dust cap, surround, and spider. All of these parts were fully FEA simulated and Klippel verified. The SA-6.5M features 5.9mm one-way linear excursion by 70% BL, 7mm by CMS, and 6.28mm by LE on Klippel. Thanks to the efficient motor venting and ample voice coil the power handling is rated for 110-watts full range / 200-watts with a 70hz HPF filter with a respectable 89dB sensitivity. As with the SA-1T this is a 4th generation SA speaker due to the SA component set from prior generations. For this iteration we optimized it further and also created a new custom-tooled frame. The revised frame is more aerodynamics and also allows for superior coil ventilation. As with most Sundown products you will find a thick magnet-ID Faraday ring as well. Last, but absolutely not least, we have the SA-8M which takes linear stroke to yet another level. We were able to achieve 9mm one-way linear by 70% BL and nearly 10mm by CMS and LE standards. As with the 3M, the 8M features a pole sleeve and magnet ID faraday ring for LE treatment. This unit is an absolute powerhouse for mid-bass, and we believe it will make big waves in the SQ world. On the output side it has a 91.5dB sensitivity and will handle 130-watts full-range / 250-watts with a 70Hz HPF thanks to the efficient motor venting and huge 2" coil. The SA-8M is all-in on SQ and output potential – the Sundown way! Sold As A Pair Includes Metal Grille Built as Full Range with lot of low end extension 30W RMS 150W RMS @HPF 300hz+ Cutout: 3.1" Outer Diameter: 3.6" Depth: 1.91"

The SA-3M three-inch midrange is built for premium builds and has premium materials. It comes with a carbon fiber cone and is tuned extraordinarily low, allowing for an outstanding soundstage and exceptional clarity. It also comes with a custom metal grille. Sold As A Pair 4ohm voice coil Includes Metal Grille Built as a full range speaker with a lot of low-end extension 30W RMS 150W RMS @HPF 300hz+ Cutout: 3.1" Outer Diameter: 3.6" Depth: 1.91"    

The all-new 2025 Sundown SA speaker series has been designed to make a statement. What statement, you may ask? That Sundown Audio can be just as serious about SQ as we are about SPL. Many people already know this but our subwoofers – even the ones used for crushing demos – have some of the lowest distortion on the market. We are now bringing our unique approach to the more dedicated Sound Quality market. Starting at the upper end of the frequency spectrum we have the SA-1T Tweeter. The SA-1T features a 25. 5m m silk dome (total 38mm including surround) driven by a powerful neodymium motor structure. The dome features a compact, tuned back chamber which helps it to achieve its extremely low FS around 700hz. This gives you an enormous amount of flexibility in choosing the crossover. The tweeter can be used as a 2-way with the 6. 5M or the 8M models or as part of a three way with either and the 3M model. In addition to the low FS and smooth response the SA-1T has a very high 92dB sensitivity so it doesn't take much power to get loud enough for just about anyone. The SA-1T is the 4th generation SA tweeter building on the success of the tweeter found in the SA Component sets over three generations. Headed down the spectrum to the midrange we have the SA-3M. This "little" unit is something incredibly special and is a favorite project of lead product designer / founder Jacob Fuller. We really went all-out on this unit to address the "big 3" drivers of distortion. The SA-3M features 4. 5m m of one-way linear excursion by 70% BL (with 8mm x-mech thanks to the custom tooled frame – so no bottoming out even on powerful dynamics) and over 6mm by CMS and LE definitions on Klippel. There is essentially NO risk of the driver reaching linearity limits in most applications. The beefy motor structure is a combination of ferrite and a neodymium pole cap magnet to help us reach 84.5dB sensitivity at 1-watt. There is a double LE treatment internal to the motor via both a copper pole sleeve and an aluminum magnet ID shorting ring allowing the SA-3M to play full-range to beyond 20khz (although, for several reasons, we do suggest using a tweeter for the top-end). On the bottom end they can be high-pass crossed over at 300hz effortlessly with 150-watts of power handling (thanks to the 28mm diameter, extra-long voice coil) or even lower if needed, with less power, due to the incredibly high linear stroke. The suspension system, surround and spider, of the SA-3M took over a year of FEA simulations and testing to reach perfection and is just as important as the motor to the resulting low distortion. We gave the suspension just as much attention as we would for a full blown high-stroke subwoofer. To finish off this masterpiece we tested several different types of woven carbon fiber cones & dust caps to achieve the best FR possible. To finish off the 2025 SA speaker line we created the SA-6 . 5M and the SA-8M. Both of which can be used as a mid-bass or mid-range speaker depending on your application. Both drivers feature the same attention to detail as the 3M regarding the carbon cone and dust cap, surround, and spider. All of these parts were fully FEA simulated and Klippel verified. The SA-6 . 5M features 5.9mm one-way linear excursion by 70% BL, 7mm by CMS, and 6.28mm by LE on Klippel. Thanks to the efficient motor venting and ample voice coil the power handling is rated for 110-watts full range / 200-watts with a 70hz HPF filter with a respectable 89dB sensitivity. As with the SA-1T this is a 4th generation SA speaker due to the SA component set from prior generations. For this iteration we optimized it further and also created a new custom-tooled frame. The revised frame is more aerodynamics and also allows for superior coil ventilation. As with most Sundown products you will find a thick magnet-ID Faraday ring as well. Last, but absolutely not least, we have the SA-8M which takes linear stroke to yet another level. We were able to achieve 9mm one-way linear by 70% BL and nearly 10mm by CMS and LE standards. As with the 3M, the 8M features a pole sleeve and magnet ID faraday ring for LE treatment. This unit is an absolute powerhouse for mid-bass, and we believe it will make big waves in the SQ world. On the output side it has a 91.5dB sensitivity and will handle 130-watts full-range / 250-watts with a 70Hz HPF thanks to the efficient motor venting and huge 2" coil. The SA-8M is all-in on SQ and output potential – the Sundown way! Sold As A Pair Specs Coming Soon

The all-new 2025 Sundown SA speaker series has been designed to make a statement. What statement, you may ask? That Sundown Audio can be just as serious about SQ as we are about SPL. Many people already know this but our subwoofers – even the ones used for crushing demos – have some of the lowest distortion on the market. We are now bringing our unique approach to the more dedicated Sound Quality market. Starting at the upper end of the frequency spectrum we have the SA-1T Tweeter. The SA-1T features a 25. 5m m silk dome (total 38mm including surround) driven by a powerful neodymium motor structure. The dome features a compact, tuned back chamber which helps it to achieve its extremely low FS around 700hz. This gives you an enormous amount of flexibility in choosing the crossover. The tweeter can be used as a 2-way with the 6. 5M or the 8M models or as part of a three way with either and the 3M model. In addition to the low FS and smooth response the SA-1T has a very high 92dB sensitivity so it doesn't take much power to get loud enough for just about anyone. The SA-1T is the 4th generation SA tweeter building on the success of the tweeter found in the SA Component sets over three generations. Headed down the spectrum to the midrange we have the SA-3M. This "little" unit is something incredibly special and is a favorite project of lead product designer / founder Jacob Fuller. We really went all-out on this unit to address the "big 3" drivers of distortion. The SA-3M features 4. 5m m of one-way linear excursion by 70% BL (with 8mm x-mech thanks to the custom tooled frame – so no bottoming out even on powerful dynamics) and over 6mm by CMS and LE definitions on Klippel. There is essentially NO risk of the driver reaching linearity limits in most applications. The beefy motor structure is a combination of ferrite and a neodymium pole cap magnet to help us reach 84.5dB sensitivity at 1-watt. There is a double LE treatment internal to the motor via both a copper pole sleeve and an aluminum magnet ID shorting ring allowing the SA-3M to play full-range to beyond 20khz (although, for several reasons, we do suggest using a tweeter for the top-end). On the bottom end they can be high-pass crossed over at 300hz effortlessly with 150-watts of power handling (thanks to the 28mm diameter, extra-long voice coil) or even lower if needed, with less power, due to the incredibly high linear stroke. The suspension system, surround and spider, of the SA-3M took over a year of FEA simulations and testing to reach perfection and is just as important as the motor to the resulting low distortion. We gave the suspension just as much attention as we would for a full blown high-stroke subwoofer. To finish off this masterpiece we tested several different types of woven carbon fiber cones & dust caps to achieve the best FR possible. To finish off the 2025 SA speaker line we created the SA-6 . 5M and the SA-8M. Both of which can be used as a mid-bass or mid-range speaker depending on your application. Both drivers feature the same attention to detail as the 3M regarding the carbon cone and dust cap, surround, and spider. All of these parts were fully FEA simulated and Klippel verified. The SA-6 . 5M features 5.9mm one-way linear excursion by 70% BL, 7mm by CMS, and 6.28mm by LE on Klippel. Thanks to the efficient motor venting and ample voice coil the power handling is rated for 110-watts full range / 200-watts with a 70hz HPF filter with a respectable 89dB sensitivity. As with the SA-1T this is a 4th generation SA speaker due to the SA component set from prior generations. For this iteration we optimized it further and also created a new custom-tooled frame. The revised frame is more aerodynamics and also allows for superior coil ventilation. As with most Sundown products you will find a thick magnet-ID Faraday ring as well. Last, but absolutely not least, we have the SA-8M which takes linear stroke to yet another level. We were able to achieve 9mm one-way linear by 70% BL and nearly 10mm by CMS and LE standards. As with the 3M, the 8M features a pole sleeve and magnet ID faraday ring for LE treatment. This unit is an absolute powerhouse for mid-bass, and we believe it will make big waves in the SQ world. On the output side it has a 91.5dB sensitivity and will handle 130-watts full-range / 250-watts with a 70Hz HPF thanks to the efficient motor venting and huge 2" coil. The SA-8M is all-in on SQ and output potential – the Sundown way! Impedance 4 ohm RMS Watts 130 Max Watts 250 Max Frequency 20Khz Min Frequency 70hz Xmax 9mm QES 0.334 VAS 21.892 QMS 6.696 QTS 0.318 RE 3.2 Outer Diameter 8.26 Cutout Diameter 7.28 Mounting Depth 3.4 Magnet Material Ferrite Surround Material Rubber Basket Material Aluminum

100W Watts RMS Mounting depth: 4.7" Diagonal measurement: 6.25" Motor diameter: 3.5" Frequency response: 4khz-20khz Sensitivity: 105dB Impedance: 4 ohms Ferrite motor Sold individually Nothing says “loud” like horns in a PA system. Handling 100 watts, the SDEH-04 allows you to place the music right where you want it. Extremely efficient and with incredibly low distortion, Sundown horn drivers don’t just play loud – they project, so you’re heard over everyone else. Dimensions Cut-Out 4" x 4" Frame Outer Diameter 4.5" x 4.5" Mounting Depth 4.7" Frequency Response

Sparked Innovations subwoofer featuring quality construction for powerful bass reproduction. Designed for car audio enthusiasts seeking excellent performance at accessible price point. Part of Sparked Innovations' growing audio product lineup.

The Sundown Audio VEX series is our top-of-the-line high efficiency mid-range series. The first entry, the VEX-10, was designed to make a splash featuring a 500-watts RMS power rating thanks to its enormous 3” coil (with a full 20mm winding length) and highly efficient airflow system consisting of twelve gaps vents and a chamfered, large-diameter pole vent. The long coil also affords the VEX-10 a full 9mm of linear x-max one-way so it can play lower than many other high-efficiency drivers without distortion. The inductance is kept in check by a dual shorting-ring system (magnet ID & pole cap) which drops the LE spec to less than 25% of the RE value. This allows the high-frequency extension to reach all the way up to 4,000 Hz where it then falls of naturally and smoothly on its own thanks to the extremely strong and non-resonant carbon-fiber cone & dust-cap assembly. Most high-efficiency drivers utilize very light- weight paper which is great for sensitivity but not so great in terms of breakup modes and strength (to withstand torture in bass-heavy vehicles). We went with real carbon-fiber to address these issues at the expense of more mass. But we still achieved a 96.6dB sensitivity by combining a large diameter, high- strength ferrite motor with a neodymium pole-cap magnet! The whole package is held together with a sturdy cast-aluminum frame that features extensive spider cavity venting to further increase thermal power handling. Quite simply – if you are looking for one of the loudest and best-sounding high efficiency midrange drivers to hit the car-audio market the VEX-10 is exactly what you need! Features Power Handling: 500 Watts RMS Impedance: 4/8-ohm SVC Vented cast frame 3 inch voice coil X-Max 9mm Excellent for Mid-bass Mounting Depth : Aproximately  4.79 inches Rear Vented Spring Loaded Terminals Specifications T/S SPECS VEX-10 S4 OHM RE (Ohms) 3.950 FS (Hz) 60.393 VAS (L) 22.517 Qes 0.165 Qms 3.859 Qts 0.159 BL

Power Handling: 500 Watts RMS Impedance: 4/8-ohm SVC Vented cast frame 3-inch voice coil X-Max: 9mm Carbon fiber cone Excellent for Mid-bass High strength ferrite motor Dual shorting rings for smooth response Mounting depth : 5.2" Rear Vented Spring Loaded Terminals With an enormous 2.5” voice coil and a super-efficient cooling system, the VEX handles 300 watts of power with ease. We went with real carbon-fiber cone to handle high SPL systems without breakup, and achieved a 94.3dB sensitivity by combining a large diameter, high strength ferrite motor with a neodymium pole-cap magnet! A sturdy cast-aluminum frame features extensive spider cavity vents to further increase thermal power handling. The Sundown Audio VEX is one of the loudest, best sounding high-efficiency midrange drivers in existence.

The Sundown Audio VEX series is our top-of-the-line high-efficiency mid-range series. The first entry, the VEX-12, was designed to make a splash featuring a 500-watt RMS power rating thanks to its enormous 3” coil (with a full 20mm winding length) and highly efficient airflow system consisting of twelve gaps vents and a chamfered, large-diameter pole vent. The long coil also affords the VEX-12 a full 9mm of linear x-max one-way so it can play lower than many other high-efficiency drivers without distortion. The inductance is kept in check by a dual shorting-ring system (magnet ID & pole cap) which drops the LE spec to less than 25% of the RE value. This allows the high-frequency extension to reach up to 4,000 Hz where it then falls off naturally and smoothly on its own thanks to the extremely strong and non-resonant carbon-fiber cone & dust-cap assembly. Most high-efficiency drivers utilize very lightweight paper which is great for sensitivity but not so great in terms of breakup modes and strength (to withstand torture in bass-heavy vehicles). We went with real carbon fiber to address these issues at the expense of more mass. But we still achieved a 96.6dB sensitivity by combining a large diameter, high-strength ferrite motor with a neodymium pole-cap magnet! The whole package is held together with a sturdy cast-aluminum frame that features extensive spider cavity venting to further increase thermal power handling. Quite simply – if you are looking for one of the loudest and best-sounding high-efficiency midrange drivers to hit the car audio market the VEX-12 is exactly what you need! Features Power Handling: 500 Watts RMS Impedance: 4/8-ohm SVC Vented cast frame 3 inch voice coil X-Max 9mm Excellent for Mid-bass Rear Vented Spring Loaded Terminals

Power Handling: 200 Watts RMS Impedance: 4 or 8-ohm SVC Vented cast frame 2.5-inch voice coil X-Max: 9mm Carbon fiber cone Excellent for Mid-bass High strength ferrite motor Dual shorting rings for smooth response Mounting depth : 4" Rear Vented Spring Loaded Terminals With an enormous 2.5” voice coil and a super-efficient cooling system, the VEX handles 200 watts of power with ease. We went with real carbon-fiber cone to handle high SPL systems without breakup, and achieved a 94dB sensitivity by combining a large diameter, high strength ferrite motor with a neodymium pole-cap magnet! A sturdy cast-aluminum frame features extensive spider cavity vents to further increase thermal power handling. The Sundown Audio VEX is one of the loudest, best sounding high-efficiency midrange drivers in existence.

Power Handling: 200 Watts RMS Impedance: 4 or 8-ohm SVC Vented cast frame 2.5-inch voice coil X-Max: 9mm Carbon fiber cone Excellent for Mid-bass High-strength ferrite motor Dual shorting rings for smooth response Mounting depth: 4" Rear Vented Spring Loaded Terminals With an enormous 2.5” voice coil and a super-efficient cooling system, the VEX handles 200 watts of power with ease. We went with a real carbon-fiber cone to handle high SPL systems without breakup, and achieved a 94dB sensitivity by combining a large diameter, high-strength ferrite motor with a neodymium pole-cap magnet! A sturdy cast-aluminum frame features extensive spider cavity vents to further increase thermal power handling. The Sundown Audio VEX is one of the loudest, best-sounding high-efficiency midrange drivers in existence. Specifications T/S SPECS VEX-6 S4 OHM RE (Ohms) 3.95 FS (Hz) 118.43 VAS (L) 3.02 Qes 0.3 Qms 3.6 Qts 0.28 Sens (1w/1m) 94 dB

The Sundown Audio VEX series is our top-of-the-line high efficiency mid-range series. The VEX-8 was designed to handle an enormous 300-watts RMS thanks to its generous 2.5” coil (with a full 20mm winding length) and highly efficient airflow system consisting of twelve gaps vents and a chamfered, large-diameter pole vent. The long coil also affords the VEX-8 a full 9mm of linear x-max one-way so it can play lower than many other high-efficiency drivers without distortion. The inductance is kept in check by a dual shorting-ring system (magnet ID & pole cap) which drops the LE spec to less than 25% of the RE value. This allows the high-frequency extension to reach all the way up to 5,000 Hz where it then falls of naturally and smoothly on its own thanks to the extremely strong and non-resonant carbon-fiber cone & dust-cap assembly. Most high-efficiency drivers utilize very light-weight paper which is great for sensitivity but not so great in terms of breakup modes and strength (to withstand torture in bass-heavy vehicles). We went with real carbon-fiber to address these issues at the expense of more mass. But we still achieved a 94.3dB sensitivity by combining a large diameter, high-strength ferrite motor with a neodymium pole-cap magnet! The whole package is held together with a sturdy cast-aluminum frame that features extensive spider cavity venting to further increase thermal power handling. Quite simply – if you are looking for one of the loudest and best-sounding high efficiency mid-range drivers to hit the car-audio market the VEX-8 is exactly what you need! Features Power Handling: 300 Watts RMS Impedance: 4/8-ohm SVC Vented cast frame 3 inch voice coil X-Max 9mm Excellent for Mid-bass Mounting Depth : Aproximately  4 inches Rear Vented Spring Loaded Terminals Specifications T/S SPECS VEX-8 S8 OHM RE (Ohms) 6.000 FS (Hz) 90.592 VAS (L) 5.861 Qes 0.249 Qms 3.539 Qts 0.232 BL (NA) 22.995 Mms (Grams) 38.524 Cms (uM/N) 8

Power Handling: 300 Watts RMS Impedance: 4/8-ohm SVC Vented cast frame 2.5-inch voice coil X-Max: 9mm Carbon fiber cone Excellent for Mid-bass High strength ferrite motor Dual shorting rings for smooth response Mounting depth : 4" Rear Vented Spring Loaded Terminals With an enormous 2.5” voice coil and a super-efficient cooling system, the VEX handles 300 watts of power with ease. We went with real carbon-fiber cone to handle high SPL systems without breakup, and achieved a 94.3dB sensitivity by combining a large diameter, high strength ferrite motor with a neodymium pole-cap magnet! A sturdy cast-aluminum frame features extensive spider cavity vents to further increase thermal power handling. The Sundown Audio VEX is one of the loudest, best sounding high-efficiency midrange drivers in existence.

Sundown Audio X Series 6.5" & 8" Drop-In Kit These are standard drop-in recone kits ONLY. If you need a custom recone kit, you will still need to call us to place your order. ** Due to shortage on parts, some recones are taking longer than expected, please be patient as we work on getting yours read** **There are no refunds or exchanges with drop-in re-cone kits.  Please make sure you are ordering the correct model, version and impedance prior to ordering.**