DC Audio Amplifiers

DC Audio Wire Ends. Accepts 1/0 wire and fits into a 1/0 input (includes 2 total units) 1 positive and 1 negative. Does not include the amplifier Machined From Aluminum Made in the USA

DC Audio Wire Reducers (includes 2 total units) 1 positive and 1 negative. Does not include the amplifier They will reduce your 1/0 awg cable to fit in a 4 awg terminal. Machined From Aluminum Made in the USA

DC Audio Wire Reducers (includes 2 total units) 1 positive and 1 negative.  They will reduce your 2/0 awg cable to fit in a 1/0 terminal. Machined From Aluminum Made in the USA Amplifier not included

DC Audio Wire Ends. Accepts 4awg wire and fits into a 4awg input (includes 2 total units) 1 positive and 1 negative. Does not include the amplifier Machined From Aluminum Made in the USA

DC Audio Wire Reducers (includes 2 total units) 1 positive and 1 negative. Does not include the amplifier They will reduce your 4 awg cable to fit in a 8 awg terminal. Machined From Aluminum Made in the USA

DC Audio Pitbull 20k Amplifier The Pitbull 20k competition series amplifier is rated as a 20,000 watt mono block. It comes with a bass knob that has a built in Clipping indicator. It is designed for 12-volt systems and will not function over 16.0 volts. Charging over 16.0 or running below 1 ohm will void your warranty.  Output Power (RMS): 7,500x1 @ 4 ohms 14.4 volts 13,000x1 @ 2 ohms 14.4 volts 20,000x1 @ 1 ohms 14.4 volts  Key Features: 1 ohm stable Variable low pass filter Variable subsonic filter Variable bass boost RCA Pass Thru Wired remote control Clipping Indicator 8awg Speaker Terminals Triple 1/0awg Power and Ground Inputs Tiffany Style RCA jacks HD End Plates Full Specs:   DC Amp Model: Pitbull 20k Input Sensitivity 6V~0.2V Frequency Response 15Hz~270Hz 24dB / Octave Crossover YES Low Pass 35Hz ~ 250Hz Subsonic Filter 10Hz-50hz Bass Boost @45hz 0 ~ 9db Phase Shift 0 ~ 180 Remote Control Yes Clip Indicator Yes Signal to Noise Ratio dB100 Damping Factor 150< THD @ 4ohms Less than 0.1% Fuse Rating External 660 amp x 3 LED Status Lights Power and Protect Master/Slave No Heatsink Length 37.75"/958mm Heatsink Width 11.5"/292mm Heatsink Height 2.6"/66mm   Output Graph:

DC 1.2k Amplifier The 1.2kw competition series amplifier is a 1,200 watt rated mono block. It is capable of running up to 16 volts for up to 1500 watts. It is a linkable amp and designed to run a 1 ohm per amp or 2 ohms when strapped for up to 3000 watts from a pair. Output Power (RMS): 4 ohm 350Wx1 @ 14.4 Volts 2 ohm 700Wx1 @ 14.4 Volts 1 ohm mono 1200x1 @ 14.4 Volts 1 ohm mono 1500x1 @ 16.0 Volts Key Features: 1 ohm stable Variable low pass filter Variable subsonic filter Variable bass boost Wired Bass Knob remote control RCA Pass Thru Linkable  Full Specs: DC Amp Model: 1.2k Input Sensitivity 6V~0.2V Frequency Response 15Hz~270Hz 24dB / Octave Crossover YES Low Pass 35Hz ~ 250Hz Subsonic Filter 10Hz-50hz Remote Control Yes Signal to Noise Ratio dB100 Damping Factor 100< THD @ 4ohms Less than 0.1% Fuse Rating External 120 amp LED Status Lights Power and Protect Heatsink Length 16.60"/419mm Heatsink Width 9.38"/238mm Heatsink Height 2.35"/59.6mm

DC Audio 2.5k Amplifier The 2.5k competition series amplifier is rated as a 2,500 watt mono block. It is a linkable amp and designed to run a 1 ohm per amp or 2 ohms when linked for almost 6000 watts from a pair. It comes with a bass knob and a clipping indicator. Output Power (RMS): 1000x1 @ 4 ohms 14.4 volts 1700x1 @ 2 ohms 14.4 volts 2500x1 @ 1 ohms 14.4 volts 5000x1 @ 2 ohm 14.4 volts LINKED 2900x1 @ 1 ohm 16.0 volts 5800x1 @ 2 ohm 16.0 volts LINKED Key Features: 1 ohm stable Variable low pass filter Variable subsonic filter Variable bass boost RCA Pass Thru Linkable Wired remote control Clipping indicator 8awg Speaker Terminals 1/0awg Power and Ground Inputs Tiffany RCA Jacks MAX VOLTAGE 16.0 VDC  Full Specs:  DC Amp Model: 2.0k Input Sensitivity 6V~0.2V Frequency Response 12Hz~264Hz 24dB / Octave Crossover YES Low Pass 35Hz ~ 250Hz Subsonic Filter 10Hz-50hz Bass Boost @45hz 0 ~ 9db Phase Shift 0 ~ 180 Remote Control Yes Clip Indicator Yes Signal to Noise Ratio dB98 Damping Factor 400< THD @ 4ohms Less than 0.1% Fuse Rating External 250 amp LED Status Lights Power and Protect Master/Slave YES Heatsink Length 13.78"/350mm Heatsink Width 9.38"/238mm Heatsink Height 2.35"/59.6mm

DC Audio 250 x 4 Amplifier The 250.4 competition series amplifier is a 250 watts per channel @ 4 ohms or 400 watts per channel @ 2 ohms. It is not 1 ohm stable. We know a lot of our customers love their low end ground pounders but want their mids and highs to keep up. That's why we offer such a large 4 channel amp. Output Power (RMS): 4 ohm 250Wx4 @ 14.4 Volts 2 ohm 400Wx4 @ 14.4 Volts 4 ohm mono 850Wx2 @ 14.4 Volts 1700 watts total power Key Features: Variable high pass filter Variable low pass filter Power / Protect / Clip status Leds 8awg Speaker Connections 1/0 awg Power / Ground inputs Class D Full Specs: DC Amp Model: 250.4 Input Sensitivity 6V~0.2V Frequency Response 20Hz~20KHz 12dB / Octave Crossover YES High Pass 20(200)Hz - 800(8K)Hz, x10 muliply Low Pass 50(500)Hz - 800(8K)Hz, x10 muliply Crossover Selector Switch HPF / FULL / LP / BP Remote Control YES With Clipping Light Signal to Noise Ratio dB95 Damping Factor 130< THD @ 4ohms Less than 0.1% Fuse Rating External 200 amp LED Status Lights Power and Protect / Clipping Heatsink Length 13.78"/350mm Heatsink Width 9.38"/66mm Heatsink Height 2.35"/59.6mm

DC Audio 3.5k Amplifier The 3.5k competition series amplifier is rated as a 3500 watt mono block. It is a linkable amp and designed to run a 1 ohm per amp or 2 ohms when linked for up to 11,000 watts from a pair. It comes with a bass knob and a clipping indicator. Output Power (RMS): 750x1 @ 4 ohms 14.4 volts 1800x1 @ 2 ohms 14.4 volts 3500x1 @ 1 ohms 14.4 volts 7000x1 @ 2 ohm 14.4 volts LINKED 4000x1 @ 1 ohm 16.0 volts 8000x1 @ 2 ohm 16.0 volts LINKED 5100x1 @ 1 ohm 18.0 volts 11000x1 @ 2 ohm 18.0 volts LINKED  Key Features: 1 ohm stable Variable low pass filter Variable subsonic filter Variable bass boost RCA Pass Thru Linkable Wired remote control Clipping indicator 8awg Speaker Terminals 1/0awg Power and Ground Inputs  Full Specs:   DC Amp Model: 3.5k Input Sensitivity 6V~0.2V Frequency Response 20Hz~250Hz 24dB / Octave Crossover YES Low Pass 35Hz ~ 250Hz Subsonic Filter 10Hz-50hz Bass Boost @45hz 0 ~ 9db Phase Shift 0 ~ 180 Remote Control Yes Clip Indicator Yes Signal to Noise Ratio dB100 Damping Factor 200< THD @ 4ohms Less than 0.1% Fuse Rating External 350 amp LED Status Lights Power and Protect Master/Slave YES Heatsink Length 21.26"/540mm Heatsink Width 9.38"/238mm Heatsink Height 2.35"/59.6mm

DC Audio 90 x 4 Amplifier The 90.4 Competition series 4 Channel amplifier. This amp has a fully active crossover and lots of clean power for the SQ minded builds. It's also fits installs where you may want to amplify your front stage and bridge the rear 2 channels to your sub stage and have a bass knob to control it. Versatility is what this amp is all about. The High-Quality parts and a HD heatsink make this amp one of the best on the market. Output Power (RMS): 4 ohm 90Wx4 @ 14.4 Volts 2 ohm 130Wx4 @ 14.4 Volts 4 ohm mono 250Wx2 @ 14.4 Volts 500 Watts total power Key Features: Variable high pass filter Variable Band pass filter 8awg Speaker Connections  4awg Power / Ground inputs Input mode Switch Class A/B Fully Active Crossover Full Specs: DC Amp Model: 90.4k Input Sensitivity 6V~0.2V Frequency Response Hz20Hz~20KHz 12dB / Octave Crossover YES CH1/2Subsonic Filter 10Hz ~ 100Hz Crossover 50Hz(500Hz) ~ 5ooHz(5KHZ ) Multiply x1, x10 Crossover Selector Switch HPF / FULL / LP-BP Bass Boost 0~18dB CH3/4Subsonic Filter 10Hz ~ 100Hz Crossover 50Hz(500Hz) ~ 5ooHz(5KHZ ) Multiply x1, x10 Crossover Selector Switch HPF / FULL / LP-BP Bass Boost 0~18dB Remote Control YES Frequency Response Hz20-20Khs Signal to Noise Ratio dB105 Damping Factor 200< THD @ 4ohms Less than 0.1% Fuse Rating On Board 80 amp LED Status Lights Power and Protect Heatsink Length 14.00"/350mm Heatsink Width 9.38"/238mm Heatsink Height 2.35"/59.6mm

DC Audio Buttons for controlling different parts of your system Latched LED DC Lasered Buttons with Harness Lasered on BASS/Mids&Highs/Lighting/Fans/Alternators Logo on switch Use a 18.5mm Drill bit for the mounting hole You must pick from the drop down what one you want. It will come with 1 button, 1 wire harness 

Amplifier Plexi Rear Cover for DC Audio Amplifiers

Amp Bars can be painted with Plasti Dip.   This is a labor service to coat a new amplifiers aluminum bars only

The 9.0k competition series amplifier is rated as a 9000 watt mono block. It is a linkable amp and designed to run a 1 ohm per amp or 2 ohms when linked for up to 22,000 watts from a pair. It comes with a bass knob. Output Power (RMS): 2,400x1 @ 4 ohms 14.4 volts 4,800x1 @ 2 ohms 14.4 volts 9,000x1 @ 1 ohms 14.4 volts 18,000x1 @ 2 ohm 14.4 volts LINKED 9,800x1 @ 1 ohm 16.0 volts 19,600x1 @ 2 ohm 16.0 volts LINKED 11,000x1 @ 1 ohm 18.0 volts 22,000x1 @ 2 ohm 18.0 volts LINKED Key Features: 1 ohm stable Variable low pass filter Variable subsonic filter Variable bass boost RCA Pass Thru Linkable Wired remote control 8awg Speaker Terminals Triple 1/0awg Power and Ground InputsFull Specs: DC Amp Model:9.0kInput Sensitivity6V~0.2VFrequency Response20Hz~250Hz24dB / Octave CrossoverYESLow Pass35Hz ~ 250HzSubsonic Filter10Hz-50hzBass Boost @45hz0 ~ 9dbPhase Shift0 ~ 180Remote ControlYesClip IndicatorNoSignal to Noise RatiodB100Damping Factor250THD @ 4ohmsLess than 0.1%Fuse RatingExternal 300 amp x 3LED Status LightsPower and ProtectMaster/SlaveYESHeatsink Length34.64"/880mmHeatsink Width11.5"/292mmHeatsink Height2.6"/66mm

2 Aluminum Terminals that converts your 2 positive and 2 negative 8 awg speaker terminals into 4 positive and 4 negative 8 awg speaker Terminals  OCTA

Machined DC Dual 0 awg Inputs 1 set ( 2 units ) This is to allow you to run double the amount of wire to your amplifiers when squeezing out every last watt the amplifier is capable of. It will fit any of our amplifiers with on board 1/0 inputs. Depending on the amplifier you may need more than 1 set of them. Made in the USA Using High Quality Aluminum Whats needed for each amplifier is listed below. 2.0 / 3.5 = 1 set 5.0 / 7.5 = 2 sets 9.0 / 10.0 / 20.0 "PITBULL" = 3 sets

Amplifier Description The DC-PS1000x1 is a Full Bridge compact series amplifier capable of making 1,000 watts. It can be used as a Subwoofer amp or to power stunt walls and doors. It has 4awg inputs and onboard clipping lights. It also comes with a bass knob. Designed to make more power in less space. Output Power (RMS) 4 ohm 400Wx1 @ 14.4 Volts 2 ohm 700Wx1 @ 14.4 Volts 1 ohm mono 1000x1 @ 14.4 Volts Key Features 1 ohm stable Operating Voltage 9-16.5v Variable low pass filter Variable subsonic filter Full Range Switch Wired Bass Knob remote control Bass Boost Onboard Power / Protect / Clip light Tiffany Style RCA Jacks Super Compact Design AMP SPECS: DC Amp Model: PS 1000.1 Input Sensitivity 4V~0.4V Frequency Response 10Hz~20kHz 12dB / Octave Crossover YES Low Pass 50Hz ~ 15kHz Subsonic Filter Yes Bass Boost Yes Phase Shift No Remote Control Yes Clip Indicator Yes Signal to Noise Ratio dB90 Full Range Switch Yes< THD @ 4ohms Less than 0.1% Fuse Rating External 100 amp LED Status Lights Power/Protect/Clip Master/Slave No Heatsink Length 5.4"/137mm Heatsink Width 5.23"/133mm Heatsink Height 2.3"/60.0mm

Amplifier Description The DC-PS1200x4 is a compact series full bridge amplifier capable of making 1,200 watts. It’s High power 4 Channel amplifier. It has 4awg inputs and can be ran 4 ohms per channel, 2 ohms per channel or bridged at 4ohms Output Power (RMS) 4 ohm 190Wx4 @ 14.4 Volts 2 ohm 300Wx4 @ 14.4 Volts 4ohm rms bridged power : 600W x 2 Key Features 4 ohm bridged stable 2 ohm stereo stable Variable low pass filter Variable High pass filter Full Range Output 9-16.5 Volts Capable x10 Crossover Switches Tiffany Style RCA Jacks Power / Protect LED AMP SPECS: DC Amp Model: PS-1200x4 Input Sensitivity 4V~0.4V Frequency Response 10Hz~20KHz 12dB / Octave Crossover YES High / Low Pass 50Hz ~ 500Hz Subsonic Filter NO Bass Boost @45hz NO Phase Shift NO Remote Control NO Clip Indicator No Signal to Noise Ratio dB90 Damping Factor 90< THD @ 4ohms Less than 1% Fuse Rating External 100 amp LED Status Lights Power/Protect Master/Slave NO Heatsink Length 7.76"/197mm Heatsink Width 5.23"/133mm Heatsink Height 2.3"/60.0mm  

Amplifier Description The DC-PS2000x1 is a Full Bridge compact series amplifier capable of making 2,000 watts. Its High power mono block that can be used as a subwoofer amp or a full range stunt wall doors amp. . It has 4awg inputs and onboard clipping lights. It also comes with a bass knob. Designed to make more power in less space. Output Power (RMS) 4 ohm 500Wx1 @ 14.4 Volts 2 ohm 1000Wx1 @ 14.4 Volts 1 ohm mono 2000x1 @ 14.4 Volts Key Features 1 ohm stable Operating Voltage 9-16.5v Variable low pass filter Variable subsonic filter Full Range Switch Wired Bass Knob remote control Bass Boost Onboard Power / Protect / Clip light Tiffany Style RCA Jacks Super Compact Design Built in fan AMP SPECS: DC Amp Model: PS 2000.1 Input Sensitivity 4V~0.4V Frequency Response 10Hz~20kHz 12dB / Octave Crossover YES Low Pass 50Hz ~ 15kHz Subsonic Filter Yes Bass Boost Yes Phase Shift No Remote Control Yes Clip Indicator Yes Signal to Noise Ratio dB90 Full Range Switch Yes< THD @ 4ohms Less than 0.1% Fuse Rating External 200 amp LED Status Lights Power/Protect/Clip Master/Slave No Heatsink Length 6.82"/173mm Heatsink Width 5.23"/133mm Heatsink Height 2.3"/60.0mm

Amplifier Description The DC-PS3000x1 is a Full Bridge compact series amplifier capable of making 3,000 watts. Its High power mono block. It has 4awg inputs and onboard clipping lights. It also comes with a bass knob. Designed to make more power in less space. Output Power (RMS) 4 ohm 900Wx1 @ 14.4 Volts 2 ohm 1800Wx1 @ 14.4 Volts 1 ohm mono 3000x1 @ 14.4 Volts Key Features 1 ohm stable Operating Voltage 9-16.5v Variable low pass filter Variable subsonic filter Full Range Switch Wired Bass Knob remote control Bass Boost Onboard Power / Protect / Clip light Tiffany Style RCA Jacks Super Compact Design AMP SPECS: DC Amp Model: PS 3000.1 Input Sensitivity 4V~0.4V Frequency Response 10Hz~20kHz 12dB / Octave Crossover YES Low Pass 50Hz ~ 15kHz Subsonic Filter Yes Bass Boost Yes Phase Shift NO Remote Control Yes Clip Indicator Yes Signal to Noise Ratio dB90 Full Range Switch Yes< THD @ 4ohms Less than 0.1% Fuse Rating External 200 amp LED Status Lights Power/Protect/Clip Master/Slave NO Heatsink Length 8.98"/228mm Heatsink Width 5.23"/133mm Heatsink Height 2.3"/60.0mm

Amplifier Description The DC-PS8000x1 is a Full Bridge compact series amplifier capable of making 8,000 watts. It’s High power mono block. It has 1/0 inputs and onboard clipping lights. It also comes with a bass knob. Designed to make more power in less space. Can be used as a subwoofer amplifier or switched into full mode for full range stuntwalls and doors Output Power (RMS) 4 ohm 2000Wx1 @ 14.4 Volts 2 ohm 4000Wx1 @ 14.4 Volts 1 ohm mono 8000x1 @ 14.4 Volts Key Features 1 ohm stable Operating Voltage 9-16.5v Variable low pass filter Variable subsonic filter Full Range Switch Wired Bass Knob remote control Bass Boost Onboard Power / Protect / Clip light Tiffany Style RCA Jacks Super Compact Design AMP SPECS: DC Amp Model: PS 8000.1 Input Sensitivity 4V~0.4V Frequency Response 10Hz~20kHz 12dB / Octave Crossover YES Low Pass 50Hz ~ 15kHz Subsonic Filter Yes Bass Boost Yes Phase Shift No Remote Control Yes Clip Indicator Yes Signal to Noise Ratio dB90 Full Range Switch Yes< THD @ 4ohms Less than 0.1% Fuse Rating External 500 amp LED Status Lights Power/Protect/Clip Master/Slave No Total Length 15.0"/381mm Heatsink Width 5.23"/133mm Heatsink Height 2.3"/60.0mm

2 Aluminum Terminals that converts your 2 positive and 2 negative 8 awg speaker terminals into 4 positive and 4 negative 8 awg speaker Terminals 

SAE Clamp Battery Terminal Flat 4 Lug Aluminum Sold in pairs. Machined in the USA from Aluminum Will accept (4) Lugs Per Terminal Battery Not Included