COMPLETE BASS PACKAGE – Includes the B2 Audio DVPE212 Dual 12" Loaded Subwoofer Enclosure and B2 Audio MANI-600 Monoblock Amplifier, delivering a full 1000W RMS system with deep, powerful bass right out of the box. ENGINEERED FOR PERFORMANCE – The DVPE212 enclosure is tuned to 35 Hz with dual 90° curved ports, internal bracing, and Acoustilux damping for smooth airflow, accurate response, and tight, controlled lows. HEAVY-DUTY CONSTRUCTION – Dual baffles, reinforced slot ports, and corner bracing eliminate flex under heavy load. Designed to fit most trunks with a slanted back for more volume and better airflow. CLEAN, EFFICIENT DESIGN – Amplifier controls are hidden behind a removable side panel for a sleek, compact installation while maintaining easy access for tuning. B2 Audio DVPE212 1000W Loaded Dual 12" Subwoofer Enclosure w/ Mono Amplifier This listing includes: (1) B2 Audio DVPE212 Loaded Enclosure (1) B2 Audio MANI-600 Monoblock Amplifier The B2 Audio DVPE212 isn't just another prefab box - it's a fully engineered enclosure designed to perform like custom work. With features usually reserved for high-end builds, this dual 12" vented enclosure comes pre-loaded with RAVE12 subwoofers and delivers massive output, tight bass response, and long-lasting durability. Engineered Performance Advanced bracing & airflow design - Corner bracing, dual slot ports, and wedged construction eliminate flex and improve sound accuracy. Optimized port tuning - Dual 90 curved ports are tuned to 35 Hz for deeper, smoother bass response without chuffing. Acoustilux damping - Reduces unwanted resonance, ensuring tight, controlled low-end performance. Built for Bass Enthusiasts Perfect fitment - Designed to span the width of most trunk spaces with an angled back for increased internal volume. Wider frequency response - Plays from 25 Hz-200 Hz, giving you both chest-pounding lows and clear midbass. Flexible wiring - Run at 1 ohm or 4 ohm to match your amplifier setup. Heavy-Duty Construction Non-pressed coated paper cones with dual 2.5" copper voice coils for strength and heat dissipation. Massive motor structure - Four 80 oz magnets per woofer for serious control and excursion. No-flex build - Dual baffles, reinforced slot ports, and rigid bracing maximize performance under heavy power. DVPE212 Specifications Frequency Response: 25 Hz - 200 Hz Sensitivity: 91 dB Impedance: Dual 2 Ohm Tuning Frequency: 35 Hz Power Handling: 1000W Enclosure Volume: 3.05 cu. ft. (86.3 L) Port Area: 11.7 in (192 cm) Port Length: 6.2" Configuration: Dual 12" Loaded (RAVE12) Voice Coil: 2.5" Copper Magnet: (4) x 80 oz Gross Weight: 68 lbs (31 kg) DVPE212 Dimensions: Length: 33" Height: 14.96" Depth: 16.53" Don’t be discouraged by the numbers - the MANI-600 is designed to run the DVPE212 enclosure with maximum efficiency. Its high damping factor, clean signal path, and tightly matched impedance curve allow it to deliver far more real-world output than its rated wattage suggests. This amp and enclosure were engineered together for optimal performance, ensuring deep, controlled bass and long-term reliability without wasted power. Mani 600 Specifications RMS Power @ 4 ohm 14.4v 90 dB Input Sensitivity: 5v ~ 0.35v Power Terminal Gauge: 6 Gauge Fuse Rating: 70 Amps Damping Factor: >400 High level input: Yes Mani 600 Crossover Circuit: Crossover Circuit: 24 dB / Oct Low Pass Crossover: 50 Hz - 500 Hz High Pass Crossover: N/A Subsonic Crossover: 5 Hz - 40 Hz Bandpass Crossover: N/A Mani 600 Measurements: Length: 10.6" Width: 6.45" Height: 2.28" Weight: 3.3 lb
